@tom-elliott
OK that would make since. I’d say that is not an issue.

I was jumping back and forth from 1.5.4 to 1.6 yesterday trying to get some kind of stability. Currently I’m on 1.5.4 and have moved on to other projects. But… Would love to get things going again to multicast. PM me if you have any ideas please.

Thanks!

I tried editing the file and rebooted the server. Fog services no longer started. I will try to wait for the new version of Fog and only image 5 clients at a time…

@tom-elliott
Yes, I found the issue was that I had picked the wrong option on the new Profile. It was set to PartImage instead of Partclone. Changed that option and it deployed properly.

@tom-elliott When I updated the master to the working branch, the three nodes immediately reconnected. I then updated the nodes too. (Two nodes are offline, will get them updated when they get back online). I also realized that some of the memory in the server wasn’t showing up. I think that is a large part of the problem. Ordering some more now…

@george1421 Hi George,

The issue was fixed, need to test it on more machines to make sure it’s a global a fix, but after isolating the boot drive using debug mode it appears to be deploying to the correct drive. I used /dev/sda2 as my host primary disk.

I’ve attached a photo of the drives available to the fog.

I’ll! keep you updated on this and thanks !

Bill.


@tombagley ignoring a mac in fogs webif just ignores it for the specific host not the whole system!

@waynejitehead i simply remove the usb nics mac after deployment because it does not belong to the system, this way new hosts with same usb nics mac will propperl recognized.

Regards X23

@bmacadre Try to put the FOG Server on one of the 100Mbps ports. This would obviously severely hinder unicast imaging, but if you’re mostly doing multicast then this might work better.

@george1421 Fog has been working, but I haven’t had any machines to test a multicast on since we last spoke. I am going to attempt to image a classroom today and will report back.

@george1421 I replicated my images using rsync and verified that all images are in both locations. I also have a backup of my images off of both of the nodes. I went in and I created a new Storage Group. I associated the Storage Node that is not the Master Server with the new Storage Group. I then associated a number of my images with that Storage Group. My goal is to have some images only reside on the node in the new Storage Group and some only reside on the other Storage Group. I set both servers to be the Master Node for their Storage Group. Based on the warning I read about setting a server to the Master Node I half-way expected for any images that were not associated with that Storage Group to be purged from the Master Node but that didn’t seem to happen, which is fine. Is it now safe to go back and purge images from servers via cli if they reside in an image store on a node that is not in the Storage Group that is associated with that image? Thank you!

We have ended up rebuilding our image and it is now working OK. It mustn’t have liked something in our old image.

Thanks for your help and suggestions!

@george1421 Ok, sorry about not getting back to this sooner, but work has been a bit busy. So anyway, I made the changes to the config file. (basically I created the ltsp.conf because it did not exist in the dnsmasq.d directory) there was only a README file. I was able to do a TCP dump and cap the information. But I have a feeling it will not be much help,

0_1532033995049_pcap.fog.JPG

I did see that I am running 2.75 version of dnsmasq, but I can reload the VM to just before I installed DNSMASQ and make sure the 2.76 version is installed. *will update if there are any changes from that versioning.

Thanks for the help!

Can you confirm

The FOG webgui is reachable On the switch where the target computer is: Ensure that spanning tree is configured for fast-STP or RSTP or place an unmanged switch between the target computer and the building switch.

@tom-elliott
It turns out that the crappy HP procurve 1900 switch that my xenserver was connected to has a feature called “auto DOS” that was blocking the NFS packets. I installed a couple of physical Linux systems to test with and found that I could mount the NFS shares when I was plugged into a different switch.

All works as it should after turning off “auto Dos” under security settings on the switch. The crazy thing is that I had a working fog server for years on this same switch/xenserver. Time to upgrade that switch. Anyway, thanks for all your help. Much appreciated!

@tom-elliott Wow, you’re awesome! We’re actually getting a new network because of E-Rate within the next month. I am logging your explanation/suggestions and will run this by the guys installing the switches. Thanks.

@wayne-workman Thanks. I changed it to 15 minutes. I’ll see how that does.

@Mike-Fahey As George said, the ACPI messages should be ok to ignore for now. About the CPU stall, find some posts from other users in the forums:
https://forums.fogproject.org/topic/8918/fog-boot-to-fos-rcu_sched-self-detected-stall-on-cpu

Not sure if this is the same issue. Please read through the whole post start to end and see if it helps.

@hvaransky This error has nothing to do with debug mode I reckon. Did you set a kernel name in that client’s host settings?? Or maybe you changed the general FOG configuration in the web UI?!

@alex84 reading the post I see no issues with what @Wayne-Workman has asked.

If indeed capture takes forever but deploy is fast as your post suggests, what is the compression set too? What is the RAM (size/speed)? What is the disk?(ssd/spinner) is the disk good?

@wayne-workman
Thank you workman, I will read the Wiki page.
Thanks again.