Windows 10 Domain Issue

[Joe Schmitt]

The legacy client does not support Windows 10 domain joining unfortantly.

[Towndrunk]

@Joe-Schmitt so the version that I’m using at this time does not support Windows 10 domain joining?

[Joe Schmitt]

You have to use the new client that comes with trunk to get windows 10 support.

[Towndrunk]

@Joe-Schmitt I did update to trunk. The version that I’m running right now has the option for a Windows 10 image. I’m able to capture and deploy a Windows 10 image using those settings. I just can’t get it to join the domain.

[Tom Elliott]

@Towndrunk I feel a need to clarify.

Windows 10 and Legacy Client will not work automatically, but it can work.

In the Windows 10 Image, get the RSAT Tools and enable (Follow this path)
Remote Server Administration Tools->Role Administration Tools->AD DS And AD LDS Tools->AD DS Tools->AD DS Snapin-ins and Command-line Tools

You don’t need anything else installed/enabled in RSAT for Domain joining to work on Windows 10 with the legacy client. However, I would not recommend using this as a means as it does enable the system to have relatively easy enabled access to actually look at and manage your Domain Controller from any system in your environment that has received this image. It will work, but it’s just easier to switch to the new client.

[Tom Elliott]

@Towndrunk The client is not FOG itself. The client is a separate file that you must install on the system images. FOG’s GUI having “Windows 10” in the list is only relevant to the image it’s referencing, it has nothing to do with the FOG Client software.

[Wayne Workman]

@Tom-Elliott @Towndrunk OR install the new client on your image.
https://wiki.fogproject.org/wiki/index.php?title=FOG_Client#The_Different_Installers

There are two different clients. Legacy client and new client. You need the new client.

Updating to trunk does not mean all your images have the new client. Your images remain unchanged, in fact. You have to update them. Remove the old client, install the new client, re-capture and everything will work.

[Towndrunk]

@Tom-Elliott OK, I think I understand. Once I updated to Trunk, I went to “Service Configuration” and under “Client Management” and installed the new client from there before I made a new image. Looking at both the PC I made captured the image from, and the PC I deployed it to, they are both running FOG Service v 0.11.3

Is that the Client that you are talking about?

[Joe Schmitt]

Please upload the fog.log from one of your problem hosts here. (Usually c:\fog.log).

[Towndrunk]

@Joe-Schmitt This is the log file from a PC that I just tried to deploy to. Windows 10 works fine, but not on the domain like in the past with Windows 7. I’m sure I have something wrong. I see the following in the log, but from that same PC right now I can reach the DC. Not sure what I have wrong.

7/14/2016 2:36 PM Client-Info Client Version: 0.11.3
7/14/2016 2:36 PM Client-Info Client OS: Windows
7/14/2016 2:36 PM Client-Info Server Version: 8537
7/14/2016 2:36 PM Middleware::Response Success
7/14/2016 2:36 PM HostnameChanger Checking Hostname
7/14/2016 2:36 PM HostnameChanger Hostname is correct
7/14/2016 2:36 PM HostnameChanger Attempting to join active directory
7/14/2016 2:36 PM HostnameChanger The specified domain either does not exist or could not be contacted, code = 1355

0_1468597067288_fog.log

[Tom Elliott]

Based on the error I’m seeing:

https://social.technet.microsoft.com/Forums/en-US/6407eba2-58ac-4b07-9cf5-bddcffdcf19c/error-1355-the-specified-domain-either-does-not-exists-etc?forum=identitylifecyclemanager

It sounds like it just can’t find your domain so it cannot connect to the domain.

[Towndrunk]

@Tom-Elliott I wasn’t sure if that had something to do with the settings or something else. Once the PC boots after the image is deployed, and I log in, I can add it to the domain manually with the same credentials/information I entered into FOG.

[Wayne Workman]

@Towndrunk In the AD settings in FOG, are you using the FQDN or a sloppy name?

[Towndrunk]

@Wayne-Workman I’m using the FQDN, Ottawacc.local I have tried it both ways, and in all three locations. . . Settings, Group, and Host settings.

[Wayne Workman]

@Towndrunk Try loosing the .local part.

[Towndrunk]

@Wayne-Workman I will try it again now, with just Ottawacc. Is there one setting that overrides the other? If I am going to use this for every computer, would it be best to put it in the FOG Settings, or the Group Settings?

[Wayne Workman]

@Towndrunk said in Windows 10 Domain Issue:

Is there one setting that overrides the other?

Not sure what you’re referring to.

If I am going to use this for every computer, would it be best to put it in the FOG Settings, or the Group Settings?

First in FOG Settings, then use groups to apply the defaults. When it’s in FOG Settings, inside groups when you check the join domain checkbox - and the fields are already cleared - it’ll populate with the defaults you have in FOG Settings.

Also - just putting these things in FOG Settings ONLY will not automatically change settings on hosts. You have to tell fog to do this. This allows FOG to manage domain joining settings on a per-host basis. At my work, we have one fog server that joins computers to 2 different domains.

[Towndrunk]

I think I found the issue. I had the settings in the Default FOG Settings, and had the “Join Domain after image task” checked in the Group, but there was no information in the settings. I unchecked it, and checked it again, and it populated with the data from the FOG Settings. It is now working like it should. Using Ottawacc.local. Thanks for the help.

[fry_p]

@Towndrunk said in Windows 10 Domain Issue:

I think I found the issue. I had the settings in the Default FOG Settings, and had the “Join Domain after image task” checked in the Group, but there was no information in the settings. I unchecked it, and checked it again, and it populated with the data from the FOG Settings. It is now working like it should. Using Ottawacc.local. Thanks for the help.

@Tom-Elliott , just a heads up, remember I had that same issue in the past with the same workaround? Since I did my batch adding all hosts to one group to check and uncheck the join box, I haven’t had any issues.

[Wayne Workman]

@fry_p I wouldn’t call it a work around. This is how it’s done in fog. You set AD settings per-host or with groups.