DHCP FAILED
-
@jeremyvdv said in DHCP FAILED:
ensp0s25
I can’t to seem to associate the driver name with a nic.
First lets get some background info.
- What version of FOG
- What version of the FOS Linux kernel (i.e. bzImage) are you using
- What is this target hardware (model and mfg)
- Are we in uefi or bios mode on this target computer
- Is the network adapter usb or physically attached to the computer?
Next steps.
- I want you to cancel any current pending tasks. Then schedule a new capture/deploy doesn’t matter, but tick the debug checkbox before you hit the submit button.
- PXE boot the target computer. After a few screens of text that you need to clear by pressing enter you will be dropped to the FOS Linux command prompt.
- At the FOS Linux command prompt key in
lspci -nn | grep -i netif the network adapter is physically built into the device orlsusbif the network adapter is usb based. - Post the results here
-
@george1421 said in DHCP FAILED:
At the FOS Linux command prompt key in lspci -nn | grep -i net if the network adapter is physically built into the device or lsusb if the network adapter is usb based.
Thank you for your quick reply.
FOG version 1.5.7
DEBIAN 10
Linux fog 4.19.0-6-686-pae #1 SMP Debian 4.19.67-2+deb10u2 (2019-11-11) i686 GNU /Linux
Server vmware
laptop HP UEFI
network physically for laptopI look for the rest of your request.
Thank you very much -
I tested with another pc client (Dell) I do not have the problem anymore except:
could not found /dev/sda3
do you have an idea of the cause
Thank you
-
@jeremyvdv Well I’m sure you did not solve the problem on the HP system, but in the case of the Dell, if its in uefi mode AND the disk controller is in raid-on mode then the disk subsystem will be hidden from linux. It won’t be just /dev/sda3 it should be the entire disk /dev/sda.
-
@jeremyvdv Please take a picture of the error and post here.
-
GEORGE:
Hello
No I did not solve the problem on HP but I know at least that it comes from the post.
Regarding the DELL I do not understand … what should I do?
Thank you
-
Sebastian :
I do this in the day
Thanks -
@jeremyvdv said in DHCP FAILED:
Regarding the DELL I do not understand … what should I do?
The typical problem in the Dell firmware the disk controller mode is configured for Raid-ON even if the computer only has a single disk. Go into the Dell firmware (BIOS) and change this mode from Raid-ON to AHCI and then test imaging. You can leave the disk mode in AHCI mode without a problem.
-
Hello
on my dell
Whether I’m in AHCI mode or RAID mode … I always have this message:
-
@jeremyvdv said in DHCP FAILED:
Whether I’m in AHCI mode or RAID mode … I always have this message:
This isn’t a hardware issue or a FOG issue, but you have bitlocker enabled on that target computer. This is a warning from FOG saying that a partition is protected by bitlocker. If you were to clone this disk, it would not boot on the new target computer because the tpm chips are different.
Disable bitlocker on all disk partitions and attempt to capture again.
-
That’s what I understood also yes but the problem is that bitloker is not activated.
Bitlocker can be activated from the bios?
Because on windows it is notthanks a lot for your help
-
@jeremyvdv Try this:
manage-bde -status manage-bde -off C: -
that’s what I did yes.
Same problem
and the HP post always at the same point DHCP failed -
I disabled the TPM in the bios but here is the problem I have now
-
my capture is in court it’s good.
It was necessary to disable the hibernation of the hard disk.
I still have the problem on my hp for DHCP FAILED
IF you have ideas … I test everything in bios
-
@jeremyvdv said in DHCP FAILED:
I still have the problem on my hp for DHCP FAILED
What do you mean by that? We see that you get past the DHCP stuff und ran into other issues. So does the DHCP fail only on random occation??
-
Hello
When I want to capture from an HP post, I always have this message:
I can decend an image on it but not capture
Thanks for your help
-
@jeremyvdv OK for the HP lets take these steps.
- Cancel any current tasks if imaging is still setup.
- Create a new capture task, but before you hit the schedule task button tick the debug checkbox. Then schedule the task.
- PXE boot the target computer like you are going to image it.
- After several screens of text on the target computer that you must clear by pressing enter key, you will be dropped to the FOS Linux command prompt. You may see the error messages again from your last picture but the system will continue to the command prompt.
- Key in the following and post the output picture here.
lspci -nn | grep -i net - Remain in this debug mode because there maybe additional commands based on the answer provided in the picture.
What this command does is print out all of the network interfaces that the HP has onboard. It will also give us the vendor and model numbers of the network adapter. We can then use those numbers for debugging.
-
Thank you for your reply.
I can not do “|” keyboard .
I tried lots of things … an idea?
thank you -
@jeremyvdv said in DHCP FAILED:
I can not do “|” keyboard .
What language keyboard do you have? The pipe symbol ( | ) is kind of a required key for unix.
If you can’t get the pipe symbol then just run the
lspci -nnand hope we get luck that the network adapter is towards the end of the list.
