boot into windows failure after deployed image

[george1421]

@bc601 The instructions are not easy, but they are not hard either.

1. On the computer that has failed. Reschedule a FOG capture task but enable debug mode.
2. PXE boot the target computer
3. After a few enter key presses you will be dropped to a linux command prompt on the target computer.
4. key in fog to start the capture process (no worries we are going to jump out before anything is captured)
5. Press enter until you are after the step of Mounting file system (press enter)
6. When you see the step Checking mounted file system press Ctrl-C. This will drop you out to a linux command prompt again.
7. Key in df -h you should see a line that says /images on the FOS client is connected to /images/dev on the fog server. (you need this step to have a place to move the log files to.
8. Now you need to connect to the target computer’s hard drive. I find this command works most of the time ntfs-3g -o force,rw /dev/sda2 /ntfs This command will connect the drive of the target computer to the /ntfs on FOS.
9. Now navigate to the Panther directory using this command cd /ntfs/Windows/Panther
10. You can either look at those files there with vi or copy them to the FOG server so you can download them with WinSCP to review them in windows. The log files all end with .log extension.
11. If you want to copy them to the fog server this command may get you close. cp /ntfs/Windows/Panther/*.log /image Then on the fog server you can pick up those log files in the /images/dev directory.

I’ll tell you its much easier to just get a Y power cable for sata like this one and review the log files on a second computer. But the above way will work. I’ve done it several times with the steps outlined above.

[bc601]

@george1421

I Received the following error on step 8 : ntfs-3g mount: failed to access mount point /ntfs: no such file or directory

[george1421]

@bc601 Ok then run this command just before the mount.

mkdir /ntfs

[bc601]

@george1421

On the last step. Step 10. I received an error message stating the following
CANNOT CREATE REGULAR FILE '/IMAGES/DDACLSSYS.LOG:READ ONLY FILE SYSTEM.
This error repeated for each .log file. I also included the screenshot of the rights to the /images folder.

[george1421]

@bc601 Did you create a capture or deploy task. Only a capture task will allow you to write to images (/images/dev on fog server).

[bc601]

@george1421

Ok it was a success. I now have the log files. I noticed something weird the setup.log file is empty and spelled incorrectly

[george1421]

@bc601 in there you have setupact == setup activity log. and setup error logn. Where did you get those files from>

I haven’t figured this out quite yet. But I’ve found these files in c:\windows\panther and c:\windows\setup\sysprep sometimes. You probably should see both places. Also I suspect the setup error [setuperr.log] to contain the reason why your OOBE failed. Sorry I can’t be more specific its been about 6 months since I last debugged a deployment.

[bc601]

@george1421

I have no idea were they came from.

So how do I correct the setup error ?

[bc601]

@george1421

Okay found out what the issue was. I did not sysprep the image correctly went back and syspreped the PC used for the image and tried it again. This time it worked after redeploying the image

[Wayne Workman]

@bc601 said in boot into windows failure after deployed image:

I did not sysprep the image correctly went back and syspreped the PC used for the image and tried it again. This time it worked after redeploying the image

Do you know what you did wrong? What did you do differently?

[bc601]

@wayne-workman

Yes I did not activate the sysprep application. Once I activated it and recaptured the image. The problem was resolved.