Using FOG to PXE boot into your favorite installer images

[george1421]

Fedora 26 Workstation

1. First we’ll create the required directories:

mkdir -p /images/os/fedora/W26
mkdir -p /tftpboot/os/fedora/W26

2. Now we’ll mount the Fedora 26 Workstation installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/Fedora-Workstation-Live-x86_64-26-1.5.iso /mnt/loop

cp -R /mnt/loop/* /images/os/fedora/W26
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/fedora/W26/isolinux/vmlinuz /tftpboot/os/fedora/W26
cp /images/os/fedora/W26/isolinux/initrd.img /tftpboot/os/fedora/W26

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.FedoraW26
   Description: Fedora Workstation v26
   Parameters:
   kernel tftp://${fog-ip}/os/fedora/W26/vmlinuz
   initrd tftp://${fog-ip}/os/fedora/W26/initrd.img
   imgargs vmlinuz initrd=initrd.img root=live:nfs://${fog-ip}/images/os/fedora/W26/LiveOS/squashfs.img ip=dhcp repo=nfs://${fog-ip}/images/os/fedora/W26 splash quiet
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Fedora Workstation v26 from the FOG iPXE boot menu.

Reference:
https://forums.fedoraforum.org/showthread.php?t=310643

[george1421]

OpenSuSE Leap 42.3

Note: I have not personally tested this configuration. When I went to download the OpenSuse ISO it was going to take about 3hrs on my FIOS internet connection. I tried a few times and the download as interrupted each time. So I decided, "I don't got time for this". I put together these instructions based on dead reckoning on what was needed. Will it work?? YMMV

1. First we’ll create the required directories:

mkdir -p /images/os/opensuse/Leap43.2
mkdir -p /tftpboot/os/opensuse/Leap43.2

2. Now we’ll mount the OpenSuSE Leap 43.2 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/openSUSE-Leap-42.3-DVD-x86_64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/opensuse/Leap43.2
umount /mnt/loop

3. At this point we need to go out and download the network/usb kernel and initrd files from the OpenSuSE site. We’ll create a temp directory, download and mount the iso image as we have done before. Then extract the two files we need.

cd /tmp
wget http://download.opensuse.org/distribution/leap/42.3/iso/openSUSE-Leap-42.3-NET-x86_64.iso
mount -o loop -t iso9660 /tmp/openSUSE-Leap-42.3-NET-x86_64.iso /mnt/loop
cp /mnt/loop/boot/x86_64/loader/linux /tftpboot/os/opensuse/Leap43.2
cp /mnt/loop/boot/x86_64/loader/initrd /tftpboot/os/opensuse/Leap43.2
umount /mnt/loop

rm -rf /tmp/openSUSE-Leap-42.3-NET-x86_64.iso

Note: If you get to the point of booting into the installer and the installer keeps asking for a cdrom, you have the wrong initfs. You must have the initrd file from the OpenSuSE Net/USB boot ISO.
4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
Set the following fields
Menu Item: os.OpenSuSEL42-3
Description: OpenSuSE Leap 42.3
Parameters:
kernel tftp://${fog-ip}/os/opensuse/Leap43.2/linux
initrd tftp://${fog-ip}/os/opensuse/Leap43.2/initrd
imgargs linux initrd=initrd ip=dhcp repo=nfs://${fog-ip}:/images/os/opensuse/Leap43.2/
boot || goto MENU
Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick OpenSuSE Leap 42.3 from the FOG iPXE boot menu.

Reference:
https://tr.opensuse.org/SDB:Network_Installation_of_SuSE_Linux_via_PXE_Boot

[george1421]

Debian 9.2

1. First we’ll create the required directories:

mkdir -p /images/os/debian/9.2
mkdir -p /tftpboot/os/debian/9.2

2. Now we’ll mount the Debian 9.2 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/debian-9.2.1-amd64-xfce-CD-1.iso /mnt/loop

cp -R /mnt/loop/* /images/os/debian/9.2
umount /mnt/loop

3. At this point we need to go out and download the netboot kernel and initrd files from the Debian site. We’ll create a temp directory, download the tar ball and extract the two files we need.

cd /tmp
mkdir netboot
cd /tmp/netboot
wget http://ftp.nl.debian.org/debian/dists/stretch/main/installer-amd64/current/images/netboot/netboot.tar.gz
tar -zxf netboot.tar.gz
cd ./debian-installer/amd64
cp linux /tftpboot/os/debian/9.2
cp initrd.gz /tftpboot/os/debian/9.2
cd /tmp
rm -rf ./netboot

Note: If you get to the point of booting into the installer and the installer keeps asking for a cdrom, you have the wrong initfs. You must have the initrd file from the Debian netboot package. Unlike other distributions, the netboot files are not on the typical installation media as far as I found.
4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
Set the following fields
Menu Item: os.Debian92
Description: Debian 9.2.1
Parameters:
kernel tftp://${fog-ip}/os/debian/9.2/linux
initrd tftp://${fog-ip}/os/debian/9.2/initrd.gz
imgargs linux initrd=initrd.gz root=/dev/nfs netboot=nfs nfsroot=${fog-ip}:/images/os/debian/9.2/ ip=dhcp rw
boot || goto MENU
Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Debian 9.2.1 from the FOG iPXE boot menu.

References:
http://students.mimuw.edu.pl/~bassa/uo/linux-adv/debian-install-pxe-netboot.pdf

[george1421]

Ubuntu 16.04.03

1. First we’ll create the required directories:

mkdir -p /images/os/ubuntu/16.04
mkdir -p /tftpboot/os/ubuntu/16.04

2. Now we’ll mount the Ubuntu 16.04 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/ubuntu-16.04.3-server-amd64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/ubuntu/16.04
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/ubuntu/16.04/install/vmlinuz /tftpboot/os/ubuntu/16.04
# See Note2 below
cp /images/os/ubuntu/16.04/install/netboot/ubuntu-installer/amd64/initrd.gz /tftpboot/os/ubuntu/16.04

Note1: If you get to the point of booting into the installer and the installer keeps asking for a cdrom, you have the wrong initfs. This tripped me up for quite some time until I found a post that solved what I was doing wrong. The path above is accurate and works. You have been warned!!
and…
Note2: If your Ubuntu 16.04 disk image does NOT CONTAIN A NETBOOT DIRECTORY (some users are reporting this), then download http://archive.ubuntu.com/ubuntu/dists/artful/main/installer-amd64/current/images/netboot/netboot.tar.gz file and extract the initrd.gz from ubuntu-installer/amd64 directory and copy to /tftpboot/os/ubuntu/16.04. The DVD I downloaded {ubuntu-16.04.3-server-amd64.iso} contained the netboot files
4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
Set the following fields
Menu Item: os.Ubuntu1604
Description: Ubuntu 16.04.03
Parameters:
kernel tftp://${fog-ip}/os/ubuntu/16.04/vmlinuz
initrd tftp://${fog-ip}/os/ubuntu/16.04/initrd.gz
imgargs vmlinuz initrd=initrd.gz root=/dev/nfs netboot=nfs nfsroot=${fog-ip}:/images/os/ubuntu/16.04/ locale=en_US.UTF-8 ip=dhcp rw
boot || goto MENU
Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Ubuntu 16.04.03 from the FOG iPXE boot menu.

References:
https://help.ubuntu.com/community/DisklessUbuntuHowto
https://askubuntu.com/questions/476508/why-ubuntu-server-asks-to-insert-a-cd-rom-when-installed-from-pxe

[george1421]

Windows 7 and Windows 10 BIOS mode only
DO NOT USE THIS METHOD anymore. I'm leaving these instructions here for legacy reasons. This method will NOT work with UEFI based systems.

1. First we’ll create the required directories:

mkdir -p /images/os/mswindows/7Pro-x64
mkdir -p /images/os/mswindows/10Pro-x64
mkdir -p /tftpboot/mswindows/7Pro-x64
mkdir -p /tftpboot/mswindows/10Pro-x64

2. Now we’ll mount the Windows install media iso over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop /{full path where you have the iso stored}/Win7ProX64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/mswindows/7Pro-x64
umount /mnt/loop

mount -o loop /{full path where you have the iso stored}/Win10ProX64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/mswindows/10Pro-x64
umount /mnt/loop

3. Beyond this point you will need a Windows 10 workstation. You also need to be aware what version of windows 10 you current have. You need to download the proper version of Windows ADK for the version of Windows 10 you will execute these instructions on. Yes I know this is a Win7 guide. I wanted to create a single how-to for both Windows 7 and Windows 10. Since support for Win7 is up in just a few years, I have to except that Win10 will be a reality soon and get with the program.
4. Download the appropriate ADK for the version of Win10 you have from here: https://developer.microsoft.com/en-us/windows/hardware/windows-assessment-deployment-kit
5. Launch the ADK installer. You will be presented with about 15 different modules to install. You only “need” the preboot environment (WinPE) stuff. You will have an option to install a bunch of stuff. You can either pick the defaults or just narrow down your selection to the WinPE stuff.
6. It might take as long as 15 minutes to install depending on your network connection and target computer.
7. While this step is not necessairy it is also a bit of an assurance that WinPE10 will have a good install of drivers needed to boot new hardware.
8. Download the WinPE10 drivers from the Dell Enterprise site here: http://en.community.dell.com/techcenter/enterprise-client/w/wiki/11530.winpe-10-driver-pack
9. I realize that you may not be using a Dell for your imaging, don’t worry these drivers only cover network and disk subsystems.
10. Extract the winpe folder from the cab file and install it in the winpe folder in the root of drive (c:\winpe).
11. After the install launch the ADK environment from Start Button->Windows Kits->Windows ADK-><something> Make sure you run this command window as Administrator. You need admin rights to use DISM.
12. In the command window, you will probably want to change back to the root of because the path is a bit long and confusing.
13. For the rest of the instructions we’ll just go copy and paste. Its fast and quick.

cd c:\
copype amd64 C:\WinPE_amd64

Dism /Mount-Image /ImageFile:"C:\WinPE_amd64\media\sources\boot.wim" /index:1 /MountDir:"C:\WinPE_amd64\mount"

Dism /Add-Driver /Image:"C:\WinPE_amd64\mount" /Driver:"c:\winpe\x64" /Recurse /ForceUnsigned

14. Now we need to edit the WinPE startup file to have it mount our windows (samba) network share.

notepad C:\WinPE_amd64\mount\Windows\System32\Startnet.cmd
 @echo off
  echo Setting up WinPE
  wpeinit

  REM Set power configuration to Performance
  powercfg /s 8c5e7fda-e8bf-4a96-9a85-a6e23a8c635c

  echo Connecting to the remote share
  net use z: \\<server_name>\<share_name> /user:<domain\uid> <pass>
  z:
  setup.exe

15. Now that we have the settings the way we need them. Lets close the wim file and create our ISO.

Dism /Unmount-Image /MountDir:"C:\WinPE_amd64\mount" /commit

MakeWinPEMedia /ISO C:\WinPE_amd64 C:\WinPE_amd64\WinPE_amd64.iso

16. Now move the C:\WinPE_amd64\WinPE_amd64.iso file to the FOG server in the /images/os/mswindows/7Pro-x64 directory.

17. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.

18. NOTE: This instruction is for legacy bios only. If you need to boot both uefi and bios installs follow the WinPE10 section above. The issue is that memdisk utility is not supported in uefi mode, so another method is required. For bios mode memdisk IS the quickest method to boot a small iso image. https://forums.fogproject.org/topic/10944/using-fog-to-pxe-boot-into-your-favorite-installer-images/10
    In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
    Set the following fields
    Menu Item: os.Win7Pro-x64
    Description: Windows 7 Pro x64 OEM
    Parameters:
    initrd nfs://${fog-ip}:/images/os/mswindows/7Pro-x64/WinPE_amd64.iso
    chain memdisk iso raw
    boot || goto MENU
    Menu Show with: All Hosts

19. That’s it, just pxe boot your target system and pick Windows 7 Pro x64 OEM from the FOG iPXE boot menu.

For this process to function you must also setup SAMBA on your fog server below.

References:
https://forums.fogproject.org/topic/7765/pxe-booting-into-ms-windows-7-setup

[george1421]

Centos 7

1. First we’ll create the required directories:

mkdir -p /images/os/centos/7
mkdir -p /tftpboot/os/centos/7

2. Now we’ll mount the Centos 7 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/CentOS7-x86_64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/centos/7
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/centos/7/images/pxeboot/vmlinuz /tftpboot/os/centos/7
cp /images/os/centos/7/images/pxeboot/initrd.img /tftpboot/os/centos/7

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.Centos7
   Description: Centos 7 v1607 {or what ever version you are building}
   Parameters:
   kernel tftp://${fog-ip}/os/centos/7/vmlinuz
   initrd tftp://${fog-ip}/os/centos/7/initrd.img
   imgargs vmlinuz initrd=initrd.img root=live:nfs://${fog-ip}:/images/os/centos/7/LiveOS/squashfs.img ip=dhcp inst.repo=nfs:${fog-ip}:/images/os/centos/7 splash quiet
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Centos 7 from the FOG iPXE boot menu.

References:
https://forums.fogproject.org/topic/8488/how-to-pxe-boot-cent-os-7/63
https://www.tecmint.com/install-pxe-network-boot-server-in-centos-7/

[george1421]

Linux Mint

1. First we’ll create the required directories:

mkdir -p /images/os/mint/18.1
mkdir -p /tftpboot/mint/18.1

2. Now we’ll mount the Linux Mint 18.1 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/linuxmint-18.1-cinnamon-64bit.iso /mnt/loop

cp -R /mnt/loop/* /images/os/mint/18.1
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/mint/18.1/casper/vmlinuz /tftpboot/mint/18.1
cp /images/os/mint/18.1/casper/initrd.lz /tftpboot/mint/18.1

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.Mint18.1
   Description: Linux Mint 18.1
   Parameters:
   kernel tftp://${fog-ip}/mint/18.1/vmlinuz
   initrd tftp://${fog-ip}/mint/18.1/initrd.lz
   imgargs vmlinuz root=/dev/nfs boot=casper netboot=nfs nfsroot=${fog-ip}:/images/os/mint/18.1/ locale=en_US.UTF-8 keyboard-configuration/layoutcode=us quiet splash
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Linux Mint 18.1 from the FOG iPXE boot menu.

Gamienator posted an update that with Linux Mint 19, you need to add an additional kernel parameter of "toram" to the imgargs line or the kernel won't be able to mount the /tmp directory correctly and will fail into emergency mode. The updated imgargs would need to be this under LM 19.
imgargs vmlinuz root=/dev/nfs boot=casper netboot=nfs nfsroot=${fog-ip}:/images/os/mint/18.1/ locale=en_US.UTF-8 keyboard-configuration/layoutcode=us toram quiet splash
`

References:
http://labalec.fr/erwan/?p=534
https://forums.fogproject.org/topic/10939/fog-iso-booting

[george1421]

WinPE 10 for BIOS and UEFI based systems

1. First we’ll create the required directories:

mkdir -p /tftpboot/os/winpe

2. Now we’ll mount the WinPE iso over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop /{full path where you have the iso stored}/WinPE_amd64.iso /mnt/loop

cp /mnt/loop/Boot/BCD /tftpboot/os/winpe/
cp /mnt/loop/Boot/boot.sdi /tftpboot/os/winpe/
cp /mnt/loop/sources/boot.wim /tftpboot/os/winpe/
umount /mnt/loop

3. Download and install the latest wimboot kernel and extract it from the zip file.

cd /tmp
wget http://git.ipxe.org/releases/wimboot/wimboot-latest.zip
unzip wimboot-latest.zip

4. Copy the wimboot file from the archive directory to root of the /tftpboot directory (we’ll need this for every windows boot media, so we’ll place it in a common spot).

cp ./wimboot-2.6.0-signed/wimboot /tftpboot

5. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
6. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.WinPE10
   Description: WinPE 10
   Parameters:
   set tftp-path tftp://${fog-ip}
   set pe-path ${tftp-path}/os/winpe
   kernel ${tftp-path}/wimboot gui
   imgfetch --name BCD ${pe-path}/BCD BCD
   imgfetch --name boot.sdi ${pe-path}/boot.sdi boot.sdi
   imgfetch --name boot.wim ${pe-path}/boot.wim boot.wim
   boot || goto MENU
7. That’s it, just pxe boot your target system and pick WinPE 10 from the FOG iPXE boot menu.

References:

[george1421]

To keep this thread clean, I’m going to fork all discussions related to this thread into a new thread and post a cross link here. This is only done to keep the thread orderly and easy to follow. The discussions regarding this thread ARE important to vet any issues before this tutorial is converted into a wiki document.

The thread discussion are here

1. https://forums.fogproject.org/topic/11027/problems-with-using-fog-to-pxe-boot-into-your-favorite-installer

[george1421]

Ubuntu 17.10 Desktop

1. First we’ll create the required directories:

mkdir -p /images/os/ubuntu/Desk17.10
mkdir -p /tftpboot/os/ubuntu/Desk17.10

2. Now we’ll mount the Ubuntu 17.10 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/ubuntu-17.10-desktop-amd64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/ubuntu/Desk17.10
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/ubuntu/Desk17.10/casper/vmlinuz.efi /tftpboot/os/ubuntu/Desk17.10
cp /images/os/ubuntu/Desk17.10/casper/initrd.lz /tftpboot/os/ubuntu/Desk17.10

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.Ubuntu.Desktop.17.10
   Description: Ubuntu Desktop 17.10
   Parameters:
   kernel tftp://${fog-ip}/os/ubuntu/Desk17.10/vmlinuz.efi
   initrd tftp://${fog-ip}/os/ubuntu/Desk17.10/initrd.lz
   imgargs vmlinuz.efi root=/dev/nfs boot=casper netboot=nfs nfsroot=${fog-ip}:/images/os/ubuntu/Desk17.10/ locale=en_US.UTF-8 keyboard-configuration/layoutcode=us quiet splash ip=dhcp rw
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Ubuntu Desktop 17.10 from the FOG iPXE boot menu.

References:

[george1421]

Kali Linux 2017.2

At this point the instructions don't work completely. I can get the installer to boot, but it appears to want to download files from Debian to complete the installation

1. First we’ll create the required directories:

mkdir -p /images/os/kali/2017.2
mkdir -p /tftpboot/os/kali/2017.2

2. Now we’ll mount the Kali 2017.2 DVD installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/kali-linux-2017.2-amd64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/kali/2017.2
umount /mnt/loop

3. At this point we need to go out and download the netboot kernel and initrd files from the Kali site. We’ll create a temp directory, download the tar ball and extract the two files we need.

cd /tmp
mkdir netboot
cd /tmp/netboot
cd /tmp
mkdir netboot
cd /tmp/netboot
wget http://repo.kali.org/kali/dists/kali-rolling/main/installer-amd64/current/images/netboot/netboot.tar.gz
tar -zxf netboot.tar.gz
cd ./debian-installer/amd64
cp linux /tftpboot/os/kali/2017.2
cp initrd.gz /tftpboot/os/kali/2017.2
cd /tmp
rm -rf ./netboot

Note: If you get to the point of booting into the installer and the installer keeps asking for a cdrom, you have the wrong initfs. You must have the initrd file from the Debian netboot package. Unlike other distributions, the netboot files are not on the typical installation media as far as I found.
4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
Set the following fields
Menu Item: os.Kali.2017.2
Description: Kali 2017.2
Parameters:
kernel tftp://${fog-ip}/os/kali/2017.2/linux
initrd tftp://${fog-ip}/os/kali/2017.2/initrd.gz
imgargs linux initrd=initrd.gz root=/dev/nfs netboot=nfs nfsroot=${fog-ip}:/images/os/kali/2017.2/ ip=dhcp rw language=en country=US keymap=us hostname=kali domain=domain.com
boot || goto MENU
Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Kali 2017.2 from the FOG iPXE boot menu.

Note 1: If you want the gui network installer you can download this netboot gzip instead of the one referenced above: http://repo.kali.org/kali/dists/kali-rolling/main/installer-amd64/current/images/netboot/gtk/netboot.tar.gz

Note 2: When you us the netboot installer kali linux will have to download the install files from the internet even though you have them on DVD. It appears that the installer tries to mount the DVD during netboot, but since that fails it falls over to network install mode. This appears to be a feature in kali linux and not a limitation in FOG or netbooting

Note 3: You can set the majority of the values in the network installer by using a preseed file. Also with that preseed file you can direct kali linux to install from a local mirrored repository by changing some values in the preseed file below

Repository preseed file from: Offensive Security site

d-i debian-installer/locale string en_US
d-i console-keymaps-at/keymap select us

d-i mirror/country string enter information manually
d-i mirror/suite string kali
d-i mirror/codename string kali
d-i mirror/http/hostname string archive.kali.org
d-i mirror/http/directory string /kali
d-i mirror/http/proxy string
d-i clock-setup/utc boolean true
d-i time/zone string US/Eastern

# Disable volatile and security
d-i apt-setup/services-select multiselect

# Enable contrib and non-free
d-i apt-setup/non-free boolean true
d-i apt-setup/contrib boolean true

d-i partman-auto/method string regular
d-i partman-lvm/device_remove_lvm boolean true
d-i partman-md/device_remove_md boolean true
d-i partman-lvm/confirm boolean true
d-i partman-auto/choose_recipe select atomic
d-i partman/confirm_write_new_label boolean true
d-i partman/choose_partition select finish
d-i partman/confirm boolean true
d-i partman/confirm_nooverwrite boolean true

# Add our own security mirror
d-i apt-setup/local0/repository string http://archive.kali.org/kali-security kali/updates main
d-i apt-setup/local0/comment string Security updates
d-i apt-setup/local0/source boolean false
d-i apt-setup/use_mirror boolean true

# Upgrade installed packages
tasksel tasksel/first multiselect standard
d-i pkgsel/upgrade select full-upgrade
# Install a limited subset of tools from the Kali Linux repositories
d-i pkgsel/include string openssh-server openvas metasploit-framework metasploit nano

# Change default hostname
d-i netcfg/get_hostname string unassigned-hostname
d-i netcfg/get_domain string unassigned-domain
d-i netcfg/hostname string kali

# Do not create a normal user account
d-i passwd/make-user boolean false
d-i passwd/root-password password toor
d-i passwd/root-password-again password toor

popularity-contest popularity-contest/participate boolean false
d-i grub-installer/only_debian boolean true
d-i grub-installer/with_other_os boolean false
d-i finish-install/reboot_in_progress note

d-i preseed/late_command string \
    in-target wget http://192.168.101.54/postseed.sh; \
    in-target /bin/bash -x chmod 755 ./postseed.sh; \
    in-target /bin/bash -x ./postseed.sh;

Note 4: You should be able to boot a live instance of kali with these actions

mkdir /var/www/html/kali
cp /images/os/kali/2017.2/live/filesystem.squashfs /var/www/html/kali
chmod 755 /var/www/html/kali/filesystem.squashfs

And then add this parameter block to a FOG iPXE menu entry. I can say I have not tried this, but assembled the information from a few blogs.

kernel tftp://${fog-ip}/os/kali/2017.2/linux
initrd tftp://${fog-ip}/os/kali/2017.2/initrd.gz
imgargs vga=788 initrd=initrd.gz boot=live components fetch=http://${fog-ip}/kali/filesystem.squashfs

References:
Kali linux appears to be based on Debian linux. I used the foundation for Debian to create this installer.
https://www.offensive-security.com/kali-linux/kali-linux-unattended-network-install-pxe/

[george1421]

Fedora 27 Workstation

1. First we’ll create the required directories:

mkdir -p /images/os/fedora/W27
mkdir -p /tftpboot/os/fedora/W27

2. Now we’ll mount the Fedora 26 Workstation installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/Fedora-Xfce-Live-x86_64-27-1.6.iso /mnt/loop

cp -R /mnt/loop/* /images/os/fedora/W27
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/fedora/W27/isolinux/vmlinuz /tftpboot/os/fedora/W27
cp /images/os/fedora/W27/isolinux/initrd.img /tftpboot/os/fedora/W27

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.FedoraW27
   Description: Fedora Workstation v27
   Parameters:
   kernel tftp://${fog-ip}/os/fedora/W27/vmlinuz
   initrd tftp://${fog-ip}/os/fedora/W27/initrd.img
   imgargs vmlinuz initrd=initrd.img root=live:nfs://${fog-ip}/images/os/fedora/W27/LiveOS/squashfs.img ip=dhcp repo=nfs://${fog-ip}/images/os/fedora/W27 splash quiet
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Fedora Workstation v27 from the FOG iPXE boot menu.

Reference:
https://forums.fogproject.org/topic/11108/can-fog-replace-my-urbackup-server/8

[george1421]

Kali Live 2017.3 - v0.1

1. First we’ll create the required directories:

mkdir -p /tftpboot/os/kali/2017.3/live

2. Now we’ll mount the Kali Live 2017.3 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/kali-linux-2017.3-amd64.iso /mnt/loop

cp /mnt/loop/live/{initrd.img,vmlinuz,filesystem.squashfs} /tftpboot/os/kali/2017.3/live/
umount /mnt/loop

3. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
4. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.Kali.live.2017.3
   Description: Kali Live 2017.3
   Parameters:
   kernel tftp://${fog-ip}/os/kali/2017.3/live/vmlinuz
   initrd tftp://${fog-ip}/os/kali/2017.3/live/initrd.img
   imgargs vmlinuz initrd=initrd.img append boot=live components fetch=tftp://${fog-ip}/os/kali/2017.3/live/filesystem.squashfs
   boot || goto MENU
   Menu Show with: All Hosts
5. That’s it, just pxe boot your target system and pick Kali Live 2017.3 from the FOG iPXE boot menu.

References:
https://forums.fogproject.org/topic/11108/can-fog-replace-my-urbackup-server/9

[george1421]

ESXi 6.5u1

NOTE: This guidance only supports network booting of the uefi installer for ESXi. The reason for this is the fog project does not ship iPXE kernels that support the comboot function. If you want to boot your ESXi server in legacy mode you will need to compile your own specific version of undionly.kpxe to add in the IMG_COMBOOT.

1. First we’ll create the required directories:

mkdir -p /images/os/esxi/6.5u1

2. Now we’ll mount the ESXi installer iso over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/VMware-VMvisor-Installer-6.5.0.update01-5969303.x86_64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/esxi/6.5u1
umount /mnt/loop

3. Edit the boot configuration file to use NFS to access all of ESXi’s files.

# remove forward slashes from the config file
sed -i 's/\///g' /images/os/esxi/6.5u1/efi/boot/boot.cfg

Now we need to edit the/images/os/esxi/6.5u1/efi/boot/boot.cfg file to insert the prefix parameter. Insert the following line just below the title parameter. Also, be sure to replace {fog_server_ip} with the actual IP address of your fog server.

prefix=nfs://{fog_server_ip}:/images/os/esxi/6.5u1

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.esxi65u1
   Description: ESXi 6.5u1 Installer
   Parameters:
   kernel nfs://${fog-ip}:/images/os/esxi/6.5u1/efi/boot/bootx64.efi -c nfs://${fog-ip}:/images/os/esxi/6.5u1/efi/boot/boot.cfg
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick ESXi 6.5u1 Installer from the FOG iPXE boot menu.

If for some reason you can not use NFS to pxe boot into the ESXi installer you can use tftp or http. If you want to use tftp extract the ESXi install files to /tftpboot/os/esxi/6.5u1. Then update the nfs:// protocols to tftp:// Be sure to remove the ':/images' after the host name or you will have errors. (i.e. kernel nfs://${fog-ip}:/images/os/esxi would become kernel tftp://${fog-ip}/os/esxi)

References:
https://www.reversengineered.com/2015/02/11/booting-vmware-esxi-in-ipxe/
http://forum.ipxe.org/showthread.php?tid=8164

[george1421]

SystemRescueCd 5.2.2 x64

1. First we’ll create the required directories:

mkdir -p /tftpboot/os/RescueCd/5.2.2

2. Now we’ll mount the SystemRescueCd boot iso over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/systemrescuecd-x86-5.2.2.iso /mnt/loop

cp /mnt/loop/isolinux/{rescue64,initram.igz} /tftpboot/os/RescueCd/5.2.2/
umount /mnt/loop

3. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
4. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.SystemRescueCd.5.2.2
   Description: SystemRescueCd 5.2.2
   Parameters:
   kernel tftp://${fog-ip}/os/RescueCd/5.2.2/rescue64
   initrd tftp://${fog-ip}/os/RescueCd/5.2.2/initram.igz
   imgargs docache
   boot || goto MENU
   Menu Show with: All Hosts
5. That’s it, just pxe boot your target system and pick SystemRescueCd 5.2.2 from the FOG iPXE boot menu.

References:
None

[george1421]

Linux Mint 19.1 Cinnamon

1. First we’ll create the required directories:

mkdir -p /images/os/mint/19.1
mkdir -p /tftpboot/mint/19.1

2. Now we’ll mount the Linux Mint 19.1 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/linuxmint-19.1-cinnamon-64bit.iso /mnt/loop

cp -R /mnt/loop/* /images/os/mint/19.1
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory.

cp /images/os/mint/19.1/casper/vmlinuz /tftpboot/mint/19.1
cp /images/os/mint/19.1/casper/initrd.lz /tftpboot/mint/19.1

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.Mint19.1
   Description: Linux Mint 19.1
   Parameters:
   kernel tftp://${fog-ip}/mint/19.1/vmlinuz
   initrd tftp://${fog-ip}/mint/19.1/initrd.lz
   imgargs vmlinuz root=/dev/nfs boot=casper netboot=nfs nfsroot=${fog-ip}:/images/os/mint/19.1/ locale=en_US.UTF-8 keyboard-configuration/layoutcode=us toram quiet splash
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Linux Mint 19.1 from the FOG iPXE boot menu.

[george1421]

GParted 0.33.0 x86

1. First we’ll create the required directories:

mkdir -p /tftpboot/gparted
mkdir -p /tmp/gparted

2. Download the gparted zip file from sourceforge site and save it to the /tmp/gparted directory
3. Change to the /tmp/gparted directory and expand the zip file. Then change into the live directory and finally copy the required files to the tftpboot/gparted directory

cd /tmp/gparted
unzip gparted-live-0.33.0-2-i686.zip
cd live
cp {vmlinuz,initrd.img,filesystem.squashfs} /tftpboot/gparted

4. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.GParted
   Description: GParted 0.33.0
   Parameters:
   kernel tftp://${fog-ip}/gparted/vmlinuz
   initrd tftp://${fog-ip}/gparted/initrd.img
   imgargs vmlinuz initrd=initrd.img boot=live config components union=overlay username=user noswap noeject ip= vga=788 fetch=tftp://${fog-ip}/gparted/filesystem.squashfs
   boot || goto MENU

Menu Show with: All Hosts
5. That’s it, just pxe boot your target system and pick GParted 0.33.0 from the FOG iPXE boot menu.

References:
https://gparted.org/livepxe.php

[george1421]

ESXi 6.7u2

NOTE: This guidance only supports network booting of the uefi installer for ESXi. The reason for this is the fog project does not ship iPXE kernels that support the comboot function. If you want to boot your ESXi server in legacy mode you will need to compile your own specific version of undionly.kpxe to add in the IMG_COMBOOT.

1. First we’ll create the required directories:

mkdir -p /images/os/esxi/6.7u2

2. Now we’ll mount the ESXi installer iso over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/VMware-VMvisor-Installer-6.7.0.update02-13006603.x86_64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/esxi/6.7u2
umount /mnt/loop

3. Edit the boot configuration file to use NFS to access all of ESXi’s files.

# remove forward slashes from the config file
sed -i 's/\///g' /images/os/esxi/6.7u2/efi/boot/boot.cfg

Now we need to edit the/images/os/esxi/6.7u2/efi/boot/boot.cfg file to insert or modify the prefix parameter. Insert/modify the following line just below the title parameter. Also, be sure to replace {fog_server_ip} (exactly including the curly braces) with the actual IP address of your fog server. Your prefix line should look similar to this:

prefix=nfs://192.168.1.20:/images/os/esxi/6.7u2

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.esxi67u2
   Description: ESXi 6.7u2 Installer
   Parameters:
   kernel nfs://${fog-ip}:/images/os/esxi/6.7u2/efi/boot/bootx64.efi -c nfs://${fog-ip}:/images/os/esxi/6.7u2/efi/boot/boot.cfg
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick ESXi 6.7u2 Installer from the FOG iPXE boot menu.

If for some reason you can not use NFS to pxe boot into the ESXi installer you can use tftp or http. If you want to use tftp extract the ESXi install files to /tftpboot/os/esxi/6.7u2. Then update the nfs:// protocols to tftp:// Be sure to remove the ':/images' after the host name or you will have errors. (i.e. kernel nfs://${fog-ip}:/images/os/esxi would become kernel tftp://${fog-ip}/os/esxi)

[george1421]

Ubuntu 1910 Desktop

1. First we’ll create the required directories:

mkdir -p /images/os/ubuntu/Desk19.10
mkdir -p /tftpboot/os/ubuntu/Desk19.10

2. Now we’ll mount the Ubuntu 19.10 installer over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop -t iso9660 /{full path where you have the iso stored}/ubuntu-19.10-desktop-amd64.iso /mnt/loop

cp -R /mnt/loop/* /images/os/ubuntu/Desk19.10
umount /mnt/loop

3. Finally we’ll copy the pxe boot kernel and intfs to the tftpboot directory. We’ll need to download the netboot version from here: http://archive.ubuntu.com/ubuntu/dists/eoan/main/installer-amd64/current/images/netboot/netboot.tar.gz This version of bzlinuz.efi and initrd.lz support booting over an NFS share instead of the local DVD Drive.

wget http://archive.ubuntu.com/ubuntu/dists/eoan/main/installer-amd64/current/images/netboot/netboot.tar.gz
tar -zxf netboot.tar.gz
cp ./ubuntu-installer/amd64/linux /tftpboot/os/ubuntu/Desk19.10
cp ./ubuntu-installer/amd64/initrd.gz /tftpboot/os/ubuntu/Desk19.10

4. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this OS.
5. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.Ubuntu.Desktop.19.10
   Description: Ubuntu Desktop 19.10
   Parameters:
   kernel tftp://${fog-ip}/os/ubuntu/Desk19.10/linux
   initrd tftp://${fog-ip}/os/ubuntu/Desk19.10/initrd.gz
   imgargs linux root=/dev/nfs boot=casper netboot=nfs nfsroot=${fog-ip}:/images/os/ubuntu/Desk19.10/ locale=en_US.UTF-8 keyboard-configuration/layoutcode=us quiet splash ip=dhcp rw
   boot || goto MENU
   Menu Show with: All Hosts
6. That’s it, just pxe boot your target system and pick Ubuntu Desktop 19.10 from the FOG iPXE boot menu.

References:

[george1421]

Veeam Agent Rescue DVD

1. First we’ll create the required directories:

mkdir -p /tftpboot/os/veeam

2. Now we’ll mount the Veeam Recovery ISO over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop /{full path where you have the iso stored}/ VeeamRecoveryMedia.iso /mnt/loop

cp /mnt/loop/boot/BCD /tftpboot/os/veeam/
cp /mnt/loop/boot/boot.sdi /tftpboot/os/veeam/
cp /mnt/loop/sources/boot.wim /tftpboot/os/veeam/
umount /mnt/loop

3. Download and install the latest wimboot kernel and extract it from the zip file.

cd /tmp
wget http://git.ipxe.org/releases/wimboot/wimboot-latest.zip
unzip wimboot-latest.zip

4. Copy the wimboot file from the archive directory to root of the /tftpboot directory (we’ll need this for every windows boot media, so we’ll place it in a common spot).

cp ./wimboot-2.6.0-signed/wimboot /tftpboot

5. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this Veeam Recover Image.
6. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.VeeamRecovery
   Description: Veeam Agent 4
   Parameters:
   set tftp-path tftp://${fog-ip}
   set pe-path ${tftp-path}/os/veeam
   kernel ${tftp-path}/wimboot gui
   imgfetch --name BCD ${pe-path}/BCD BCD
   imgfetch --name boot.sdi ${pe-path}/boot.sdi boot.sdi
   imgfetch --name boot.wim ${pe-path}/boot.wim boot.wim
   boot || goto MENU
7. That’s it, just pxe boot your target system and pick Veeam Agent 4 from the FOG iPXE boot menu.

Bonus round NOTE: the code below doesn't work at the moment, I'm getting an HTTP access denied message. The info is right, there is just something with apache at the moment that is stopping access to these individual files
The above method shows how to load the Veeam Recover image over tftp. The following instructions show how to do the same thing over the faster http protocol.

1. First we’ll create the required directories:

mkdir -p /var/www/html/os/veeam

2. Now we’ll mount the Veeam Recovery ISO over the loop directory. Then we’ll copy the contents of the DVD to the directory we built above.

mount -o loop /{full path where you have the iso stored}/ VeeamRecoveryMedia.iso /mnt/loop

cp /mnt/loop/boot/BCD /var/www/html/os/veeam
cp /mnt/loop/boot/boot.sdi /var/www/html/os/veeam
cp /mnt/loop/sources/boot.wim /var/www/html/os/veeam
umount /mnt/loop

3. Download and install the latest wimboot kernel and extract it from the zip file.

cd /tmp
wget http://git.ipxe.org/releases/wimboot/wimboot-latest.zip
unzip wimboot-latest.zip

4. Copy the wimboot file from the archive directory to root of the /var/www/html/os directory (we’ll need this for every windows boot media, so we’ll place it in a common spot).

cp ./wimboot-2.6.0-signed/wimboot /var/www/html/os

5. The last bit of magic we need to do is setup a new FOG iPXE boot menu entry for this Veeam Recover Image.
6. In the fog WebGUI go to FOG Configuration->iPXE New Menu Entry
   Set the following fields
   Menu Item: os.VeeamRecoveryHTTP
   Description: Veeam Agent 4 (http)
   Parameters:
   set http-path http://${fog-ip}/os
   set pe-path ${http-path}/veeam
   kernel ${http-path}/wimboot gui
   imgfetch --name BCD ${pe-path}/BCD BCD
   imgfetch --name boot.sdi ${pe-path}/boot.sdi boot.sdi
   imgfetch --name boot.wim ${pe-path}/boot.wim boot.wim
   boot || goto MENU
7. That’s it, just pxe boot your target system and pick Veeam Agent 4 (http) from the FOG iPXE boot menu.