Getting PXE-EC8 error on NUC6i7KYK Skull Canyon

[Tom Elliott]

@mageta52 As you’re using PFSense for dhcp, start here:

https://wiki.fogproject.org/wiki/index.php?title=Other_DHCP_Configurations#pfSense

[Wayne Workman]

@mageta52 You might also try a firmware update on the NUC as well, it might make a difference.

[mageta52]

I just logged into the PFSense box and was set up for undionly.kpxe, I tried switching to undionly.kkpxe but got the same error. I’m assuming that the boot files under /tftpboot are the options available to me? There are a lot of them there, not sure if I should just start cycling through them, trying them all until one works?

[Wayne Workman]

@mageta52 said in Getting PXE-EC8 error on NUC6i7KYK Skull Canyon:

I’m assuming that the boot files under /tftpboot are the options available to me?

Correct.

There are a lot of them there, not sure if I should just start cycling through them, trying them all until one works?

The ones ending with .efi are for UEFI systems. You said you’re working with legacy, so you’d try everything but the .efi files, and also exclude default.ipxe because that’s a service file and not a boot file.

[george1421]

@mageta52 If I remember pfsense there is a field for bios (legacy) mode and that is typically undionly,kpxe and there is also a uefi field where you might puth ipxe.efi.

[george1421]

We use the intel nucs on our campus, not the 6i but the 5i5 models.

On the intel nucs, have you gone into the advanced firmware settings and confirmed you are in uefi or legacy(bios) mode? Also some of the nucs have a “personality” option, where you can set it for win7, win8, win10, unix make sure you have the right personality selected on the nuc. Also be sure you have the latest firmware installed on the nucs they have updates every quarter for new versions. Make sure you are up to date.

I just looked up error EC-8

PXE-EC8: !PXE structure was not found in UNDI driver code segment.
The UNDI ROM image has probably been corrupted, or has not been initialized by the BIOS. This error is most often caused by one of three things:
A .NIC image was programmed into a BIOS when a .LOM image should have been used.
The memory allocated by the POST Memory Manager ($PMM) during PXE option ROM initialization has been corrupted or erased before PXE option ROM boot.
The UNDI_Loader structure was not properly initialized during option ROM initialization.

Just a stab in the dark here, maybe a undi boot kernel was sent to a uefi based system??

[mageta52]

@george1421 Under boot options, it lists UEFI and legacy. All of the boot devices are set under legacy mode, including the NIC.

[george1421]

@mageta52 I don’t have one of the nuc’s in front of me. I seemed to recall a check box its either uefi on or off (but don’t quote me on that). And then there was a personality setting.

If you don’t know what mode it is (I can’t tell from your last post) and your fog server and nuc are on the same subnet we can use the fog server to record the dhcp booting process and that will tell us what the client is saying during bootup.

[mageta52]

@george1421I’ll run tcpdump on that interface tomorrow when I get in and see what happens during the PXE boot.

[george1421]

@mageta52 Ok, no problem.

The proper tcpdump filter that will show us what is going on without showing things that you shouldn’t post to an open forum is this.
tcpdump -w output.pcap port 67 or port 68 or port 69 or port 4011
This will record only dhcp, tftp, and dhcpProxy traffic. Start this running on the FOG server then pxe boot the target computer (on the same subnet) until the target errors out then hit ctrl-C on tcpdump and review with wireshark or post it hear for review.