Trunk install, fog.conf vhost file issue

[kurtblah]

[root@localhost bin]# systemctl restart httpd
Job for httpd.service failed because the control process exited with error code. See "systemctl status httpd.service" and "journalctl -xe" for details.

[root@localhost bin]# systemctl status httpd -l
● httpd.service - The Apache HTTP Server
   Loaded: loaded (/usr/lib/systemd/system/httpd.service; enabled; vendor preset: disabled)
   Active: failed (Result: exit-code) since Mon 2016-06-20 19:23:42 CDT; 15s ago
  Process: 2975 ExecStart=/usr/sbin/httpd $OPTIONS -DFOREGROUND (code=exited, status=1/FAILURE)
 Main PID: 2975 (code=exited, status=1/FAILURE)

Jun 20 19:23:42 localhost.localdomain systemd[1]: Starting The Apache HTTP Server...
Jun 20 19:23:42 localhost.localdomain httpd[2975]: AH00526: Syntax error on line 4 of /etc/httpd/conf.d/fog.conf:
Jun 20 19:23:42 localhost.localdomain httpd[2975]: Invalid command '2601:243:200:d722::73a8', perhaps misspelled or defined by a module not included in the server configuration
Jun 20 19:23:42 localhost.localdomain systemd[1]: httpd.service: Main process exited, code=exited, status=1/FAILURE
Jun 20 19:23:42 localhost.localdomain systemd[1]: Failed to start The Apache HTTP Server.
Jun 20 19:23:42 localhost.localdomain systemd[1]: httpd.service: Unit entered failed state.
Jun 20 19:23:42 localhost.localdomain systemd[1]: httpd.service: Failed with result 'exit-code'.```

-kurt

[Wayne Workman]

@kurtblah Sorry for so many commands. I’m working through you like I would if I were there at the terminal.

What is the output of this: ip addr show

[kurtblah]

no problem. here’s the ip addr:

[root@localhost bin]# ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether d4:85:64:01:6a:05 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.251/24 brd 192.168.1.255 scope global enp1s0
       valid_lft forever preferred_lft forever
    inet6 2601:243:200:d722::73a8/128 scope global dynamic
       valid_lft 592005sec preferred_lft 592005sec
    inet6 2601:243:200:d722:d685:64ff:fe01:6a05/64 scope global noprefixroute dynamic
       valid_lft 226861sec preferred_lft 226861sec
    inet6 fe80::d685:64ff:fe01:6a05/64 scope link
       valid_lft forever preferred_lft forever

[Wayne Workman]

@kurtblah So, do you need IPv6 on this system for some reason?

If not, here’s instructions to turn it off for you:

backup interface config:
cp /etc/sysconfig/network-scripts/ifcfg-enp1s0 /etc/sysconfig/network-scripts/ifcfg-enp1s0.old

Edit the interface config:
vi /etc/sysconfig/network-scripts/ifcfg-enp1s0

Change these lines to off or zero or no:

NETWORKING_IPV6=no
IPV6INIT=no

If the lines are not there, you can try to add them.

Restart the interface - this command is sorta dangerous if the node is far away and the config is bad, the interface could fail to come back up, so keep that in mind:

ifdown enp1s0;ifup enp1s0

After doing this, try to re-run the fog installer and see what happens. Hopefully it works.

To put the old config file back if you want:

rm -f /etc/sysconfig/network-scripts/ifcfg-enp1s0
cp /etc/sysconfig/network-scripts/ifcfg-enp1s0.old /etc/sysconfig/network-scripts/ifcfg-enp1s0
ifdown enp1s0;ifup enp1s0

Reference:
http://linoxide.com/linux-how-to/disable-ipv6-centos-fedora-rhel/

Noteworthy:
http://tecadmin.net/disable-ipv6-on-linux/#
https://www.g-loaded.eu/2008/05/12/how-to-disable-ipv6-in-fedora-and-centos/

[kurtblah]

Disabling IPv6 did the trick. I ran:

 sudo echo "1" > /proc/sys/net/ipv6/conf/all/disable_ipv6

and the installer ran normally. I’ll need to shut it down permanently.

Thank you for your help. Is this IPv6 issue consistent in all of the builds?

-kurt

[Wayne Workman]

@kurtblah probably. And there isn’t the man power to do an overhaul on that. IPV6 will have to wait for the 2.0 rewrite.

[Sebastian Roth]

Not sure if we should still change the installer script to ignore those IPv6 addresses… @Developers ?

[Wayne Workman]

@Sebastian-Roth I think the installer should ignore IPv6 addresses.

[Tom Elliott]

I’m pretty sure I’ve added the code buts to only worry about IPv4 but could use confirmation of this.

[malkazoid]

@Tom-Elliott Hi - I just ran into the same problem. I’ll go ahead disable ipv6 but thought I’d let you know the development installer grabbed from github still seems to try to include ipv6 in fog.conf