Cannot Get Capture To Work (New Server)

[nbuursma]

@george1421 said:

To acquire / steal a post from Sebastian.

“Could you please run a debug session on this device (WebGUI -> Host -> Basic tasks -> Debug) and run lsblk from the command line of the target computer? What do you get?”

We were also focused on the fog version (important to know). What device are you trying to capture (make and model). Does this have a traditional hard drive, ssd, or m.2 SSD drive?

Okay I ran it:

http://imgur.com/tVVvEj7

[nbuursma]

Oh! Okay… hmm… it appears that the x250s have a small SSD built into them perhaps?

Would that not having any partitions on it throw off Fog?

[george1421]

@nbuursma OK, that is where lenovo is hiding all of that malware lol.

I think that should be a question for the @Developers but the structure of the drives /dev/sda (etc) should not trow off FOG. But that 14GB empty hard drive might.

[Tom Elliott]

@george1421 depends on how it is seen in the system.

If the SSD is the first drive, it may pose a problem.

[george1421]

@Tom-Elliott His link to the image has this built in lenovo hard drive as /dev/sdb, where his main SATA SSD is /dev/sda. But who knows what format or partition table it has on this 14GB drive, let alone the reason why it is there truly there.

[Tom Elliott]

@george1421 We get partitions based on the drive.

If this is a resizable image, then it should get the first device found (/dev/sda in this case).

[george1421]

@Tom-Elliott Interesting. Then if we look at this picture http://imgur.com/QnoooBh can we tell if sda or sdb is thowing the error. Its not quite clear. Its coming up with an unterminated string. According to the output of lsblk it should be working no problem.

[nbuursma]

@george1421 said:

@Tom-Elliott Interesting. Then if we look at this picture http://imgur.com/QnoooBh can we tell if sda or sdb is thowing the error. Its not quite clear. Its coming up with an unterminated string. According to the output of lsblk it should be working no problem.

Okay guys, I got pretty far on my own…

I figured the small SSD was the issue so I logged into windows - > disk management -> formatted it
Then I updated the host on the fog server so Host Primary Disk = /dev/sda
This seems to work, the partclone actually images the hard drive re-sizing as it goes… it still failed though at the end when it was updating the database.

[Wayne Workman]

@nbuursma Do you know how to do a debug upload?

It’d allow you to step through the imaging process - and when the error happens, you’ll have time to take a good-looking photo with a camera and upload here for us to see. You might find some other errors too that you didn’t notice before.

[nbuursma]

@Wayne-Workman said:

@nbuursma Do you know how to do a debug upload?

It’d allow you to step through the imaging process - and when the error happens, you’ll have time to take a good-looking photo with a camera and upload here for us to see. You might find some other errors too that you didn’t notice before.

I’m kicking one off now… its so weird, it literally goes through the entire capture process and then fails at updating the database.

I’ll update this more info after the debug capture.

[nbuursma]

@Wayne-Workman said:

@nbuursma Do you know how to do a debug upload?

It’d allow you to step through the imaging process - and when the error happens, you’ll have time to take a good-looking photo with a camera and upload here for us to see. You might find some other errors too that you didn’t notice before.

Okay I dont know how to do this debug capture at all…

[Wayne Workman]

@nbuursma said:

Okay I dont know how to do this debug capture at all…

When you’re on the confirmation page for creating an image task, it’s just a little check box before you confirm the task creation. This is how it works in FOG Trunk anyways.

After your host boots up to the network for a debug upload/download you can issue the fog command to initiate the imaging task. You’d then slowly [enter] through each step.

[nbuursma]

@Wayne-Workman said:

@nbuursma said:

Okay I dont know how to do this debug capture at all…

When you’re on the confirmation page for creating an image task, it’s just a little check box before you confirm the task creation. This is how it works in FOG Trunk anyways.

After your host boots up to the network for a debug upload/download you can issue the fog command to initiate the imaging task. You’d then slowly [enter] through each step.

Got it, okay first thing that fails is
Attempting to check in… Failed

Then screen is filled with complete GARBAGE

[Wayne Workman]

@nbuursma said:

Got it, okay first thing that fails is
Attempting to check in… Failed

Then screen is filled with complete GARBAGE

Can you get us a picture?

How is it that it fails on check in, when before it failed at the very end? What changed?