Cannot deploy (download) image in 1.2.0
-
What is the name of your image?
via CLI on your fog server, can you go to:
cd /images/<name of image>/and then issue these commands and give us their output:
ls -lahRt cat d1.original.partitions;cat d1.minimum.partitions -
Clarification: when I say I did my own factory install, I meant to say “Base” install- just a standard MS win7 disk.
ubuntu 14.04
fog 1.2.0image name was “BitSecSource”
-
@netman86
Post the output of this please:cd /images/BitSecSource/;ls -lahRt;cat d1.original.partitions;cat d1.minimum.partitions -
I don’t have any .partitions files in bitsecsource;
only files in there are:
d1.mbr
d1p1.img
d1p2.img
d1p3.img
d1p4.img
d1p5.img -
ok, that’s fine… the command would have told me this…
I’d still like to know the file sizes to look for potential issues.
ls -lhaRt /images -
Could be completely wrong but I have ran into a problem that sounds similar to yours where it just skipped the imaging process for no reason. I finally figured out that apparently even though the drives showed the same size and both should be able to handle the same image, I had to shrink the partition size just a little so it was under the max size of the hard drive. Maybe give that a try?
-
I shrank partition 5 and re-imaged the machine, and now the target machine did run the restore- although partition 5 came up empty on the target machine (yet it IS formatted and has the correct label- curious!)
As requested, here’s the paste from the console- note that bitsecsource was the image that wouldn’t deploy, and source2 is the one that worked minus partition5.
/images/Source2: total 19G drwxrwxrwx 6 root root 4.0K Jul 9 16:37 .. -rwxrwxrwx 1 root root 7.5G Jul 9 16:37 d1p5.img drwxrwxrwx 2 root root 4.0K Jul 9 16:01 . -rwxrwxrwx 1 root root 296 Jul 9 16:01 d1p4.img -rwxrwxrwx 1 root root 152M Jul 9 16:01 d1p3.img -rwxrwxrwx 1 root root 11G Jul 9 15:59 d1p2.img -rwxrwxrwx 1 root root 8.2M Jul 9 15:07 d1p1.img -rwxrwxrwx 1 root root 512 Jul 9 15:07 d1.mbr /images/BitSecSource: total 18G drwxrwxrwx 6 root root 4.0K Jul 9 16:37 .. -rwxrwxrwx 1 root root 7.5G Jul 9 12:31 d1p5.img drwxrwxrwx 2 root root 4.0K Jul 9 11:54 . -rwxrwxrwx 1 root root 295 Jul 9 11:53 d1p4.img -rwxrwxrwx 1 root root 69M Jul 9 11:53 d1p3.img -rwxrwxrwx 1 root root 11G Jul 9 11:52 d1p2.img -rwxrwxrwx 1 root root 8.2M Jul 9 11:01 d1p1.img -rwxrwxrwx 1 root root 512 Jul 9 11:01 d1.mbrMod edited to use code boxes.
-
@netman86 Would you consider upgrading to FOG Trunk? Your issue might be resolved by this alone.
-
I can’t say I’ve got a compelling reason not to, assuming it’s a fairly pain free process and the TRUNK version is considered fairly stable.
This FOG machine was built just for this job (I’ve always wanted to try it out) so I don’t have too much to lose if it goes awry.
-
Since I see the d1p5 has data in the image, I’m going to upgrade to trunk and try to re-deploy to another laptop- assuming it lets me deploy an image made with 1.2.0
-
So after spending a few hours fixing everything after attempting to upgrade to trunk, I’m running trunk.
I tried to deploy the same image to another laptop and had the same issue I had in 1.2.0.
I then tried to create a NEW image from the source, and that appeared to go fine- but it overwrote my old source instead of creating a new one as I had specified (Odd issues with changing options in host management not sticking)
For whatever reason, the image didn’t work. It went through and did a partition copy, and wrote new files to /images/source2, but under image management that source shows up as 0.00B when it’s about 50G on disk.
I went and changed it to source3 again and created an upload job, which failed- I had to manually create a Source3 directory in /images/ for it to start the process, which tells me that maybe something is screwy with permissions for /images- but everything appears to be 777 so I can’t fathom what it could be.
Creating a new source3 image now just to see what happens…
-
New image appears to have created correctly, and shows up in image from the web UI with a size- but the restore back to another box had the same results.
-
update:
after the failed deployment, the size listed under image management changed to 0.00iB. Odd.
-
This post is deleted! -
@netman86 said:
update:
after the failed deployment, the size listed under image management changed to 0.00iB. Odd.
That’s a minor bug that is non-impacting. I have a few images that list as 0 in size on client, but they work just fine.
Why do you have 5 partitions?
-
- the windows 100mb boot partition
- C drive
- D drive (required for this purpose)
- extended for 5
- backup partition with image of C for on the road re-imaging (also required…)
I might be able to get away with keeping the image on partition 3 as a file, but TPTB want it on its own partition.
-
I just spoke to the guy wanting these and the requirement has changed- I also need a small (100mb) partition for the lab, so that’ll be six partitions in all.
I’m testing a RAW image clone right now, I can’t think of a reason it wouldn’t work if FOG manages to initiate the copy on the destination…
