Unable to get DHCP server to restart after restart - Ubuntu 12.04

[Wayne Workman]

What you’ve tried is correct. Below is the commands for Ubuntu DHCP start/stop/restart

[CODE]sudo service isc-dhcp-server restart
sudo service isc-dhcp-server start
sudo service isc-dhcp-server stop[/CODE]

There must be something else going on…

I assume you were able to get to the FOG menu from the target-host before? If so, then your configuration is correct.
It’s probably something simple… Check your patch cables to the target-host, the server, etc. Ensure they are snug.

Did you set a static IP for the FOG server? I know that in Fedora 21 server, it’s like impossible to get DHCP/dnsmasq to work without a static IP set prior.

[PageTown]

[quote=“Wayne Workman, post: 46383, member: 28155”]
[CODE]sudo service isc-dhcp-server restart
sudo service isc-dhcp-server start
sudo service isc-dhcp-server stop[/CODE][/quote]

Typed the “sudo service-irc-dhcp-server start” and got “isc-dhcp-server start/running, process 7890”. Am I correct to assume that this message means my DHCP server IS running?

[quote=“Wayne Workman, post: 46383, member: 28155”]
I assume you were able to get to the FOG menu from the target-host before? If so, then your configuration is correct.
It’s probably something simple… Check your patch cables to the target-host, the server, etc. Ensure they are snug.[/quote]

Yes. I had Fog up and running. I successfully uploaded three images and deployed those images out without any problems. Checked cables, tried different cables just to make sure. They’re good and Ubuntu machine acknowledges the wired connection.

[quote=“Wayne Workman, post: 46383, member: 28155”]Did you set a static IP for the FOG server? I know that in Fedora 21 server, it’s like impossible to get DHCP/dnsmasq to work without a static IP set prior.[/quote]

Yes. I set a static IP for Fog and used that IP for the DHCP service also.

I was reading on these forums that there’s a bug on Ubuntu 12.04 (Which I am using) that resets some of the IP info when the machine gets powered off? I wasn’t sure if maybe that was my issue or not.

[Joseph Hales]

Maybe check and make sure firewall is disabled?
sudo ufw disable

[Wayne Workman]

+1 about the firewall^^^. Make sure that’s off for troubleshooting purposes.

You could use TCPDump to see EXACTLY what is going on…

This should be very simple because your setup is offline and disconnected from the rest of your network.
Check out this article, and then post a PCAP file (and hopefully look at it yourself, too).

[url]http://fogproject.org/wiki/index.php/TCPDump[/url]

With this, we will be able to determine exactly what’s happening/not happening.

[PageTown]

Here’s a txt file I saved using Wireshark of the PCAP file. Let me know if this doesn’t work. The board won’t let me upload the original PCAP file.

[url=“/_imported_xf_attachments/1/1932_PageTownPCAPData.txt?:”]PageTownPCAPData.txt[/url]

[Wayne Workman]

you can compress the file as a .zip and upload…

[PageTown]

It kind of looks like my DHCP might be giving out the wrong Netmask.
On my Ubuntu wired connection and when I set up Fog, I used the following info:
Static IP:10.1.0.185
Netmask: 255.255.254.0
Gateway: 10.1.0.1
DNS: 12.127.16.67

[PageTown]

Excellent. Here it is.

[url=“/_imported_xf_attachments/1/1933_PageTownPCAPFile.zip?:”]PageTownPCAPFile.zip[/url]

[Wayne Workman]

Well if you’re running on an isolated network and are handling DHCP, then you dictate what subnet to use.

However, this subnet must match the subnet mask that is assigned to the interface that’s handling DHCP.

Since this machine is on an isolated network, gateway and DNS are not required.
I see the FOG server AND what appears to be a client asking who has 10.1.0.1

Also, the FOG server is trying to send traffic to 224.0.0.251 and 224.0.0.22. If this is an isolated network, those requests shouldn’t exist, and FOG shouldn’t be trying to communicate with anything in that range.

Also, I see lots of DHCP discover requests, but zero responses.

I’d say DHCP is misconfigured. Look through your config again. There’s some examples on various sites for setup. I think there are some examples in the WiKi too.

[Wayne Workman]

Are you using a crossover cable? if not, what device are you using to connect the fog server and the client?

[PageTown]

I am using a standard Cat5e cable. I used the same cable to upload and deploy images before the restart so I don’t think it’s the issue.

Here’s what’s in my etc/dhcp/dhcpd.conf file:

DHCP Server Configuration file.

see /usr/share/doc/dhcp*/dhcpd.conf.sample

This file was created by FOG

use-host-decl-names on;
ddns-update-style interim;
ignore client-updates;
next-server 10.1.0.185;

subnet 10.1.0.0 netmask 255.255.254.0 {
option subnet-mask 255.255.254.0;
range dynamic-bootp 10.1.0.10 10.1.0.254;
default-lease-time 21600;
max-lease-time 43200;
option domain-name-servers 127.0.0.1;
option routers 10.1.0.185;
filename “undionly.kpxe”;
}

[Wayne Workman]

[quote=“PageTown, post: 46443, member: 29454”]I am using a standard Cat5e cable. I used the same cable to upload and deploy images before the restart so I don’t think it’s the issue.
[/quote]

What is the standard Cat5e cable connected to? one end goes to the target-machine… the other end goes to what? What device?

[PageTown]

I am running Fog on an Asus K50I laptop. One end of my cable is plugged into its ethernet port. The other, the target computer.

[Wayne Workman]

Then you need a cross over cable, sir. [url]http://en.wikipedia.org/wiki/Ethernet_crossover_cable[/url]

[PageTown]

I didn’t need one before. Everything worked fine until I powered the server off. What’s changed?

[Wayne Workman]

[quote=“PageTown, post: 46457, member: 29454”]I didn’t need one before. Everything worked fine until I powered the server off. What’s changed?[/quote]

The [U]only[/U] way that setup would have worked before is if you were using a crossover cable.

So, assuming this is a cross over cable, and after the reboot, then some service must not have started up, or some other service that you don’t want DID start up… like firewall.

[PageTown]

I disabled the firewall per Joseph Hale’s suggestion. I’ll go ahead and try a crossover cable.

[PageTown]

Using a crossover cable didn’t make any difference. I’m still getting the “No DHCP or ProxyDHCP offers were received” on the PXE boot screen.

Any other ideas?

[Tom Elliott]

My guess is tftp isn’t running. Try [code]sudo service tftpd-hpa restart[/code]

[PageTown]

[quote=“Tom Elliott, post: 46461, member: 7271”]My guess is tftp isn’t running. Try [code]sudo service tftpd-hpa restart[/code][/quote]

Hi Tom. Unfortunately, this didn’t solve my issue. I have attached the logs you have mentioned in your sig if you’d like to take a look at them.

I am running [FONT=Tahoma]Fog 1.2.0 on Ubuntu 12.04. [/FONT]

[url=“/_imported_xf_attachments/1/1935_PageTown Fog logs.zip?:”]PageTown Fog logs.zip[/url]