how to change netmask and ip range?

Quazz

@onenetwork FOG should no longer overwrite your dhcp config with those settings to off. Is that not the case for you?

The submask value is located in the .fogsettings file, (along with other info such as routers and what not) which FOG will use to build the DHCP config (if you’re allowing it to control DHCP)

onenetwork

@Quazz said in how to change netmask and ip range?:

@onenetwork FOG should no longer overwrite your dhcp config with those settings to off. Is that not the case for you?

The submask value is located in the .fogsettings file, (along with other info such as routers and what not) which FOG will use to build the DHCP config (if you’re allowing it to control DHCP)

Sorry to say I can’t find anything related to submask or IP range locate in the .fogsettings files. I try to change routeraddress to 255.255.255.224 or 204.10.x.65(gateway) and it not working.
By the way I’m using fog server 1.2.0

Wayne Workman

@Quazz said in how to change netmask and ip range?:

Edit /opt/fog/.fogsettings and set blddhcp to 0 so it doesn’t generate a DHCP file and your changes remain.

Btw 255.255.255.254 would make it so only one ip is on the entire subnet, just so you know.

On older trunk and perhaps 1.2.0, the installer ignored bldhcp if dodhcp was turned on. This isn’t a problem in the current I believe but it’s been a while since I messed with the dhcp functionality.

Wayne Workman

@onenetwork On your server, what is the output of ip addr show ?

onenetwork

@Wayne-Workman said in how to change netmask and ip range?:

@onenetwork On your server, what is the output of ip addr show ?

fog@ubuntu:~$ ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:0c:19:61:5c:da brd ff:ff:ff:ff:ff:ff
    inet 204.10.185.68/27 brd 204.10.185.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe50::40c:49ff:fe61:6cda/64 scope link
       valid_lft forever preferred_lft forever
fog@ubuntu:~$

thanks

Mod edited to use code box.

onenetwork

so there is no way to fix client IP and netmask at all?
is there a file some where i can edit before update so it can bypass this? thanks all, i really need this to work.

Wayne Workman

@onenetwork there is, and it’s easy. I’m not at a computer at the moment - but when I am, I can easily construct a dhcpd.conf file that is exactly what you need - along with changes so fog 1.2.0 no longer overwrites the file. I’ll get it together sometime tonight for you.

onenetwork

@Wayne-Workman said in how to change netmask and ip range?:

@onenetwork there is, and it’s easy. I’m not at a computer at the moment - but when I am, I can easily construct a dhcpd.conf file that is exactly what you need - along with changes so fog 1.2.0 no longer overwrites the file. I’ll get it together sometime tonight for you.

Awesome!

Wayne Workman

@onenetwork

Edit your /opt/fog/.fogsettings file to set the dodhcp and bldhcp like below. Be sure to save.

vi /opt/fog/.fogsettings
Instructions on using Vi

dodhcp='N'
bldhcp='0'

Then, edit the /etc/dhcp/dhcpd.conf file to contain the below. Notice that option domain-name-servers is commented out with a # because I don’t know your preferred DNS address. If you want to set that, remove the comment and replace the x.x.x.x with the ip address - comma separated for multiple DNS addresses if you want multiple ones.

I’ve assumed from one of your below posts:

I try to change routeraddress to 255.255.255.224 or 204.10.x.65(gateway)

That the proper router address for this subnet is 204.10.185.65, so I’ve excluded this address from the DHCP range, and have defined it as a router option.

vi /etc/dhcp/dhcpd.conf

option space PXE;
option PXE.mtftp-ip    code 1 = ip-address;
option PXE.mtftp-cport code 2 = unsigned integer 16;
option PXE.mtftp-sport code 3 = unsigned integer 16;
option PXE.mtftp-tmout code 4 = unsigned integer 8;
option PXE.mtftp-delay code 5 = unsigned integer 8;
option arch code 93 = unsigned integer 16; # RFC4578

use-host-decl-names on;
ddns-update-style interim;
ignore client-updates;
next-server 204.10.185.68;
authoritative;


subnet 204.10.185.64 netmask 255.255.255.224 {
        option subnet-mask 255.255.255.224;
        range dynamic-bootp 204.10.185.66 204.10.185.94;
        default-lease-time 21600;
        max-lease-time 43200;
        #option domain-name-servers x.x.x.x;
        option routers 204.10.185.65;
 
    class "UEFI-32-1" {
    match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00006";
    filename "i386-efi/ipxe.efi";
    }

    class "UEFI-32-2" {
    match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00002";
     filename "i386-efi/ipxe.efi";
    }

    class "UEFI-64-1" {
    match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00007";
     filename "ipxe.efi";
    }

    class "UEFI-64-2" {
    match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00008";
    filename "ipxe.efi";
    }

    class "UEFI-64-3" {
    match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00009";
     filename "ipxe.efi";
    }

    class "Legacy" {
    match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00000";
    filename "undionly.kkpxe";
    }

}
host ubuntu {
    hardware ethernet 00:0c:19:61:5c:da;
    fixed-address 204.10.185.68;
}

You can copy/paste this into the vi editor as long as you’re in insert mode (see tutorial above). Pasting from windows clipboard into putty is just a right click anywhere in the window - if you’re using putty (which I would highly recommend).

After writing the file and closing it, you will need to restart dhcp. On Ubuntu that would be:
service dhcpd restart
or
service dhcpd stop
service dhcpd start

And to enable dhcpd to start on boot:
service dhcpd enable

Check the status of the dhcpd daemon on Ubuntu like this:
service dhcpd status

And - let me know if it works. If not, give me the output of service dhcpd status

onenetwork

Thank you Wayne Workman, it’s working now. also, thank you Quazz.
After copy instruction provided by Wayne Workman, changed boot to Grub style and command out /var/www/fog/lib/fog/BootMenu.class.php line 696 booturl/ipxe/bg.png it is now working perfect. This is awesome!

Wayne Workman

@onenetwork said in how to change netmask and ip range?:

changed boot to Grub style and command out /var/www/fog/lib/fog/BootMenu.class.php line 696 booturl/ipxe/bg.png

I wasn’t aware you were having problems with the background image?

Instead of commenting out code, we can help you get it working. It is a separate issue, so I would ask you to make a new thread with details on the fog version, os version, model you’re booting, any relevant network layout information, boot file, efi mode, and any other information that may be relevant.

onenetwork

Yes, background image is different issue I have learned from previous problem. Again, thank you for your helping with this netmask and IP range problem. Without your help I probably go crazy, LOL.

how to change netmask and ip range?

128

12.1k

17.3k

155.3k