Does FOG work with iSCSI?
-
@Tom-Elliott said in Does FOG work with iSCSI?:
By making the NAS a “node” you will lose such things as the ability to replicate to other nodes…
Meaning like a secondary backup?
… and multicast tasks.
You mean deploying/Imaging multiple clients?
What would you suggest in my situation, whether it’s the easiest or not, to get connected to my NAS? What would you do?
-
Ok, so change of plans. I do need help with setting up with iSCSI. I knew my NAS was iSCSI capable, but I just found out it is only iSCSI. Yeah, more learning!
-
@ManofValor I managed a Tera station at my last job. They certainly support more than just iSCSI.
I’d suggest don’t worry about multicast. Unicast in fog trunk is stupid fast already.
Figure out how to make an NFS share on it, and also share the same directory with FTP. Set a user/pass for ftp. Those are the credentials you plug into fog storage management.
All these things have been said here and other places before. You gotta sit down and dig in, and read instead of skimming - and experiment. You’ll fail many times before it works and that’s just fine. It’s called learning.
-
@Wayne-Workman said in Does FOG work with iSCSI?:
@ManofValor I managed a Tera station at my last job. They certainly support more than just iSCSI.
Actually, I called Buffalo tech and they said that particular NAS is iSCSI only.
-
@ManofValor Ok then, progress. We have to use iSCSI then. Calling them was good - that’s part of digging into this.
-
-
So now I have iSCSI enabled and connected to FOG/NAS device and should all be ready to go. I ran another image to see if it is working. Do ya’ll know if there’s something else I need to do to push it through or is it supposed to start backing up automatically? I haven’t seen anywhere yet that I need to but maybe ya’ll know something I don’t.
-
I don’t know if I follow?
-
@Tom-Elliott Basically, I’m not sure what to look for to know if the images are being sent to the NAS device. I’ve never used one so I’m not sure if there’s a delay before it starts, or if I have everything in order, or what? Is there something I have to do to push it to the NAS every time I image or Is it automatic, if I did it right? I’ve done everything I can find on this and it seemed pretty simple after figuring it all out so not sure if I’m missing anything.
-
Can anyone help me with my last question?
-
@ManofValor Is this your main storage node? Do images upload/replicate to it? Also - if properly setup everything will be automatic.
-
@ManofValor NAS = Network Attached Storage, in simple terms means a storage device (you know storage could be disk, USB key, SD card, CD, …) that is connected over network - compared to all the others being connected on an internal system bus. The data being written to any of those devices (be it the normal ones or NAS) should end up on the device without any extra “push” or something. But maybe I got your question wrong?!?
-
Where is the iSCSI device located on the FOG server? What does your Storage Node setup look like?
-
[root@localhost /]# cd /opt/fog/images [root@localhost images]# ls dev MCWP77 MCWP82 MCWPL54 postdownloadscriptsI did another image,MCWPL25, after connecting to the NAS, via iSCSI, and it is not showing up with the others. Either it worked and is on the NAS or something else happened. I also noticed this under image management:
One thing I am trying to figure out though is how to check the NAS. The interface I have doesn’t show me what’s on the disk’s. Just the size of the disk’s. I’m still learning how to use it but haven’t got much time on it. This is what I’m working on now.
-
@ManofValor No Data, under that field, just means the last known date to when that image was uploaded is not available (there’s no data to show).
-
@Tom-Elliott What about it not showing up under my /images folder?
-
@ManofValor What happens when you try to upload to that node? Screenshots please. Or are you just trying to replicate to it? If replicating, we need the replication log. It’s in the log viewer.
-
@Wayne-Workman When I ran an image for that one it worked as normal, I didn’t see anything different. It even shows up in fog management. Do you need me to do again? Here is the replicator log file if it helps. The one I’m looking for is not there, MCWPL25.
Did I need to create another storage node for the NAS. I could have swore in the process I was just pointing it the /images dir, but I could have misunderstood.
-
@ManofValor Yes, everything in fog must be defined in one place or another in the DB, which means creating it in the Web Interface. You must create a storage node definition for the NAS.
-
@Wayne-Workman Is it possible to edit my existing node or better to just create a new one?