Location of images

[george1421]

@mikmatcr How familiar are you with linux? Linux is not like windows in that it doesn’t have the concept of different disks (i.e. etc). In linux (UNIX) it has a single file system, where you can connect different disks (or network shares) to different folders (directory mount points). You can traverse between disks just like changing directories.

So if you want to have disk 1 as the system disk and disk 2 for images that can be done pretty easy (relatively), with no changes to FOG’s configuration.

The basic steps are to create a disk partition on disk 2 (/dev/sdb), then format it. Then connect that disk to a temporary location in the directory and move the contents of your /images directory to this new disk. Then finally unmount the disk temporarily and then reconnect the new disk to the /images directory.

I think I have a step by step tutorial on this. Let me check.

What host OS is the FOG server using?

[Edit] Here is a step by step, but only execute it up to and including step 7. After step 7 we will change it up a bit. https://forums.fogproject.org/topic/11048/moving-fog-s-images-files-off-the-root-partition-2017-edition

[mikmatcr]

@george1421 My knowledge in Linux is too basic. The server has Ubuntu 18

[george1421]

@mikmatcr Do you have the new drive installed in your fog server now?

If so switch over to root with sudo su -i then key in lsblk and post the results here.

[mikmatcr]

@george1421 No, now I only have 1 hard drive. But in January I will place another

[george1421]

@mikmatcr Ok no problem. Get the second hard drive installed in the server than we can walk you through the setup. It might take about 20 minutes to setup. Not to bad if you can copy and paste commands.

[mikmatcr]

@george1421 Hi, I already added the second disk, this is the result of the command:

NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
loop0    7:0    0  1008K  1 loop /snap/gnome-logs/61
loop1    7:1    0   3,7M  1 loop /snap/gnome-system-monitor/107
loop2    7:2    0  14,8M  1 loop /snap/gnome-characters/359
loop3    7:3    0  42,8M  1 loop /snap/gtk-common-themes/1313
loop4    7:4    0   4,2M  1 loop /snap/gnome-calculator/544
loop5    7:5    0  54,5M  1 loop /snap/core18/1265
loop6    7:6    0  89,1M  1 loop /snap/core/8268
loop7    7:7    0  89,1M  1 loop /snap/core/8213
loop8    7:8    0  54,6M  1 loop /snap/core18/1279
loop9    7:9    0   156M  1 loop /snap/gnome-3-28-1804/91
loop10   7:10   0 156,7M  1 loop /snap/gnome-3-28-1804/110
loop11   7:11   0   3,7M  1 loop /snap/gnome-system-monitor/111
loop12   7:12   0   956K  1 loop /snap/gnome-logs/81
loop13   7:13   0  44,2M  1 loop /snap/gtk-common-themes/1353
loop14   7:14   0     4M  1 loop /snap/gnome-calculator/406
loop15   7:15   0  14,8M  1 loop /snap/gnome-characters/367

sda      8:0    0   9,1T  0 disk 
├─sda1   8:1    0   512M  0 part /boot/efi
└─sda2   8:2    0   9,1T  0 part /
sdb      8:16   0   9,1T  0 disk 
├─sdb1   8:17   0    16M  0 part 
└─sdb2   8:18   0   9,1T  0 part /media/serv/Nuevo vol

[george1421]

@mikmatcr Ok I see you have 2 disks installed (via the lsblk) command. That second disk appears to have some data on it. Was that your intention?

[mikmatcr]

@george1421 No, I must format the second disk

[george1421]

@mikmatcr ok what I would do is run fdisk from command prompt

sudo fdisk /dev/sdb

d
p
2

d
p
1

w
e

Note it may be q to quit and not e to exit. I did that from memory.

That should delete both partitions and write them back to the disk.

Now you can start with the instructions https://forums.fogproject.org/topic/11048/moving-fog-s-images-files-off-the-root-partition-2017-edition up to and including step 7. That will create a new partition and then format it. Once you have it formatted then we can go through the steps to copy the files over and then remap the drive.

[Sebastian Roth]

@mikmatcr Did you get your disk setup or do you still need help with this?