I recently ran across this same issue, but it was not due to the fast spanning tree protocols. Our IT department added 802.1x authentication on the wired ports of all our switches, but the time out to fail back to MAC authentication was just longer than the 27 seconds @george1421 referenced in his post. We had a handful of hosts work, but a large majority failed. Our IT department had to shorten the 802.1X authentication timeout in order to make this work for us.
Best posts made by tlehrian
-
RE: Either DHCP failed or we were unable to access http://(ip)/fog//index.php for connection testing
-
RE: Error Restoring GPT Partition Tables
@george1421 Ok. I should have a chance to do this later today. I’m hopeful this leads to a fix for the issue.
-
RE: Error Restoring GPT Partition Tables
@george1421 I placed one of these machines in legacy mode to see if the drives would exhibit the same behavior and ran the tests you prescribed earlier. Indeed, after two reboots, they did switch, so we can probably rule BIOS type out. Here are the outputs:
State 1:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme0n1 259:0 0 238.5G 0 disk nvme1n1 259:1 0 477G 0 disk |-nvme1n1p1 259:2 0 499M 0 part |-nvme1n1p2 259:3 0 100M 0 part |-nvme1n1p3 259:4 0 16M 0 part |-nvme1n1p4 259:5 0 341.2G 0 part `-nvme1n1p5 259:6 0 135.1G 0 part > nvme list Node SN Model Namespace Usage Format FW Rev ---------------- -------------------- ---------------------------------------- --------- -------------------------- ---------------- -------- /dev/nvme0n1 S499NX0M113634 SAMSUNG MZVLB256HAHQ-000H2 1 2.95 GB / 256.06 GB 512 B + 0 B EXD71HAQ /dev/nvme1n1 S498NA0M403426 SAMSUNG MZVLB512HAJQ-000H2 1 149.49 GB / 512.11 GB 512 B + 0 B EXA71HAQ > nvme id-ctrl /dev/nvme0n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S499NX0M113634 mn : SAMSUNG MZVLB256HAHQ-000H2 fr : EXD71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 256060514304 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:- nvme id-ctrl /dev/nvme1n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S498NA0M403426 mn : SAMSUNG MZVLB512HAJQ-000H2 fr : EXA71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 512110190592 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:-
After one reboot, the
lsblk
command reversed the order of the listing, but still had the drives identified correctly:NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme1n1 259:0 0 477G 0 disk |-nvme1n1p1 259:2 0 499M 0 part |-nvme1n1p2 259:3 0 100M 0 part |-nvme1n1p3 259:4 0 16M 0 part |-nvme1n1p4 259:5 0 341.2G 0 part `-nvme1n1p5 259:6 0 135.1G 0 part nvme0n1 259:1 0 238.5G 0 disk
(I did not run the nvme commands in this state)
After one more reboot, the drives switched:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme0n1 259:0 0 477G 0 disk |-nvme0n1p1 259:2 0 499M 0 part |-nvme0n1p2 259:3 0 100M 0 part |-nvme0n1p3 259:4 0 16M 0 part |-nvme0n1p4 259:5 0 341.2G 0 part `-nvme0n1p5 259:6 0 135.1G 0 part nvme1n1 259:1 0 238.5G 0 disk Node SN Model Namespace Usage Format FW Rev ---------------- -------------------- ---------------------------------------- --------- -------------------------- ---------------- -------- /dev/nvme0n1 S498NA0M403426 SAMSUNG MZVLB512HAJQ-000H2 1 149.49 GB / 512.11 GB 512 B + 0 B EXA71HAQ /dev/nvme1n1 S499NX0M113634 SAMSUNG MZVLB256HAHQ-000H2 1 2.95 GB / 256.06 GB 512 B + 0 B EXD71HAQ > nvme id-ctrl /dev/nvme0n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S498NA0M403426 mn : SAMSUNG MZVLB512HAJQ-000H2 fr : EXA71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 512110190592 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:- > nvme id-ctrl /dev/nvme1n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S499NX0M113634 mn : SAMSUNG MZVLB256HAHQ-000H2 fr : EXD71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 256060514304 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:-
-
RE: Error Restoring GPT Partition Tables
I am busy getting ready for our Fall semester to start next week, BUT…
I will keep a debug task set up for one of our machines in order to do more testing for you all if need be. I’m glad to be part of the solution here, and I promise not to take as long to respond back to a testing request next time…
Latest posts made by tlehrian
-
RE: Either DHCP failed or we were unable to access http://(ip)/fog//index.php for connection testing
I recently ran across this same issue, but it was not due to the fast spanning tree protocols. Our IT department added 802.1x authentication on the wired ports of all our switches, but the time out to fail back to MAC authentication was just longer than the 27 seconds @george1421 referenced in his post. We had a handful of hosts work, but a large majority failed. Our IT department had to shorten the 802.1X authentication timeout in order to make this work for us.
-
RE: Error Restoring GPT Partition Tables
Oh, OK. I guess I misread that. I’ll check out the new inits and see what happens, but probably won’t hit this again hard until January. Thanks for the response!
-
RE: Error Restoring GPT Partition Tables
@Sebastian-Roth Looks like we’re still on 4.19.48. I have not needed to image labs since August, and don’t expect to need to do any large-scale imaging before Spring, but could certainly update and test with a newer kernel if need be.
Tim
-
RE: Error Restoring GPT Partition Tables
I’m just checking back on this (rather old) topic to see if any headway had been made. It seems the last tests I ran indicated that the
basename
commands did indicate the device names remained consistent even when the OS switches them. I won’t need to image these again for a while, but would be nice to see if a fix is available.Thanks!
Tim -
RE: Error Restoring GPT Partition Tables
I am busy getting ready for our Fall semester to start next week, BUT…
I will keep a debug task set up for one of our machines in order to do more testing for you all if need be. I’m glad to be part of the solution here, and I promise not to take as long to respond back to a testing request next time…
-
RE: Error Restoring GPT Partition Tables
@Sebastian-Roth I’m sorry it took me so long to get back to this, but I was able to run the testing this morning. It does appear that the device names stay consistent, even though the drives may change order in
lsblk
. Here are my results:State 1
> lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme1n1 259:0 0 477G 0 disk |-nvme1n1p1 259:2 0 499M 0 part |-nvme1n1p2 259:3 0 100M 0 part |-nvme1n1p3 259:4 0 16M 0 part |-nvme1n1p4 259:5 0 341.2G 0 part `-nvme1n1p5 259:6 0 135.1G 0 part nvme0n1 259:1 0 238.5G 0 disk > basename $(readlink /sys/block/nvme0n1/device) nvme0 > basename $(readlink /sys/block/nvme0n1/device/device) 0000:02:00.0 > basename $(readlink /sys/block/nvme1n1/device) nvme1 > basename $(readlink /sys/block/nvme1n1/device/device) 0000:03:00.0
State 2
> lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme0n1 259:0 0 477G 0 disk |-nvme0n1p1 259:2 0 499M 0 part |-nvme0n1p2 259:3 0 100M 0 part |-nvme0n1p3 259:4 0 16M 0 part |-nvme0n1p4 259:5 0 341.2G 0 part `-nvme0n1p5 259:6 0 135.1G 0 part nvme1n1 259:1 0 238.5G 0 disk > basename $(readlink /sys/block/nvme0n1/device) nvme1 > basename $(readlink /sys/block/nvme0n1/device/device) 0000:03:00.0 > basename $(readlink /sys/block/nvme1n1/device) nvme0 > basename $(readlink /sys/block/nvme1n1/device/device) 0000:02:00.0
Note how the
device
anddevice/device
names remain unchanged per disk. -
RE: Error Restoring GPT Partition Tables
@Quazz I was curious about the LiveCD thing, so I tried it. I can confirm that it DOES reorder the drives on successive LiveCD boots.
lsblk
switched the drive order after one successive boot.In fact I think I ran into this when first installing the OSes on these machines, and thought it was weird when it happened, but didn’t think much of it at the time.
-
RE: Error Restoring GPT Partition Tables
@george1421 I placed one of these machines in legacy mode to see if the drives would exhibit the same behavior and ran the tests you prescribed earlier. Indeed, after two reboots, they did switch, so we can probably rule BIOS type out. Here are the outputs:
State 1:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme0n1 259:0 0 238.5G 0 disk nvme1n1 259:1 0 477G 0 disk |-nvme1n1p1 259:2 0 499M 0 part |-nvme1n1p2 259:3 0 100M 0 part |-nvme1n1p3 259:4 0 16M 0 part |-nvme1n1p4 259:5 0 341.2G 0 part `-nvme1n1p5 259:6 0 135.1G 0 part > nvme list Node SN Model Namespace Usage Format FW Rev ---------------- -------------------- ---------------------------------------- --------- -------------------------- ---------------- -------- /dev/nvme0n1 S499NX0M113634 SAMSUNG MZVLB256HAHQ-000H2 1 2.95 GB / 256.06 GB 512 B + 0 B EXD71HAQ /dev/nvme1n1 S498NA0M403426 SAMSUNG MZVLB512HAJQ-000H2 1 149.49 GB / 512.11 GB 512 B + 0 B EXA71HAQ > nvme id-ctrl /dev/nvme0n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S499NX0M113634 mn : SAMSUNG MZVLB256HAHQ-000H2 fr : EXD71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 256060514304 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:- nvme id-ctrl /dev/nvme1n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S498NA0M403426 mn : SAMSUNG MZVLB512HAJQ-000H2 fr : EXA71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 512110190592 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:-
After one reboot, the
lsblk
command reversed the order of the listing, but still had the drives identified correctly:NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme1n1 259:0 0 477G 0 disk |-nvme1n1p1 259:2 0 499M 0 part |-nvme1n1p2 259:3 0 100M 0 part |-nvme1n1p3 259:4 0 16M 0 part |-nvme1n1p4 259:5 0 341.2G 0 part `-nvme1n1p5 259:6 0 135.1G 0 part nvme0n1 259:1 0 238.5G 0 disk
(I did not run the nvme commands in this state)
After one more reboot, the drives switched:
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme0n1 259:0 0 477G 0 disk |-nvme0n1p1 259:2 0 499M 0 part |-nvme0n1p2 259:3 0 100M 0 part |-nvme0n1p3 259:4 0 16M 0 part |-nvme0n1p4 259:5 0 341.2G 0 part `-nvme0n1p5 259:6 0 135.1G 0 part nvme1n1 259:1 0 238.5G 0 disk Node SN Model Namespace Usage Format FW Rev ---------------- -------------------- ---------------------------------------- --------- -------------------------- ---------------- -------- /dev/nvme0n1 S498NA0M403426 SAMSUNG MZVLB512HAJQ-000H2 1 149.49 GB / 512.11 GB 512 B + 0 B EXA71HAQ /dev/nvme1n1 S499NX0M113634 SAMSUNG MZVLB256HAHQ-000H2 1 2.95 GB / 256.06 GB 512 B + 0 B EXD71HAQ > nvme id-ctrl /dev/nvme0n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S498NA0M403426 mn : SAMSUNG MZVLB512HAJQ-000H2 fr : EXA71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 512110190592 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:- > nvme id-ctrl /dev/nvme1n1 -H NVME Identify Controller: vid : 0x144d ssvid : 0x144d sn : S499NX0M113634 mn : SAMSUNG MZVLB256HAHQ-000H2 fr : EXD71HAQ rab : 2 ieee : 002538 cmic : 0 [2:2] : 0 PCI [1:1] : 0 Single Controller [0:0] : 0 Single Port mdts : 9 cntlid : 4 ver : 10200 rtd3r : 186a0 rtd3e : 7a1200 oaes : 0 [8:8] : 0 Namespace Attribute Changed Event Not Supported oacs : 0x17 [15:4] : 0x1 Reserved [3:3] : 0 NS Management and Attachment Not Supported [2:2] : 0x1 FW Commit and Download Supported [1:1] : 0x1 Format NVM Supported [0:0] : 0x1 Sec. Send and Receive Supported acl : 7 aerl : 7 frmw : 0x16 [4:4] : 0x1 Firmware Activate Without Reset Supported [3:1] : 0x3 Number of Firmware Slots [0:0] : 0 Firmware Slot 1 Read/Write lpa : 0x3 [1:1] : 0x1 Command Effects Log Page Supported [0:0] : 0x1 SMART/Health Log Page per NS Supported elpe : 255 npss : 4 avscc : 0x1 [0:0] : 0x1 Admin Vendor Specific Commands uses NVMe Format apsta : 0x1 [0:0] : 0x1 Autonomous Power State Transitions Supported wctemp : 354 cctemp : 355 mtfa : 50 hmpre : 0 hmmin : 0 tnvmcap : 256060514304 unvmcap : 0 rpmbs : 0 [31:24]: 0 Access Size [23:16]: 0 Total Size [5:3] : 0 Authentication Method [2:0] : 0 Number of RPMB Units sqes : 0x66 [7:4] : 0x6 Max SQ Entry Size (64) [3:0] : 0x6 Min SQ Entry Size (64) cqes : 0x44 [7:4] : 0x4 Max CQ Entry Size (16) [3:0] : 0x4 Min CQ Entry Size (16) nn : 1 oncs : 0x1f [5:5] : 0 Reservations Not Supported [4:4] : 0x1 Save and Select Supported [3:3] : 0x1 Write Zeroes Supported [2:2] : 0x1 Data Set Management Supported [1:1] : 0x1 Write Uncorrectable Supported [0:0] : 0x1 Compare Supported fuses : 0 [0:0] : 0 Fused Compare and Write Not Supported fna : 0 [2:2] : 0 Crypto Erase Not Supported as part of Secure Erase [1:1] : 0 Crypto Erase Applies to Single Namespace(s) [0:0] : 0 Format Applies to Single Namespace(s) vwc : 0x1 [0:0] : 0x1 Volatile Write Cache Present awun : 1023 awupf : 0 nvscc : 1 [0:0] : 0x1 NVM Vendor Specific Commands uses NVMe Format acwu : 0 sgls : 0 [0:0] : 0 Scatter-Gather Lists Not Supported subnqn : ps 0 : mp:7.02W operational enlat:0 exlat:0 rrt:0 rrl:0 rwt:0 rwl:0 idle_power:- active_power:- ps 1 : mp:6.30W operational enlat:0 exlat:0 rrt:1 rrl:1 rwt:1 rwl:1 idle_power:- active_power:- ps 2 : mp:3.50W operational enlat:0 exlat:0 rrt:2 rrl:2 rwt:2 rwl:2 idle_power:- active_power:- ps 3 : mp:0.0760W non-operational enlat:210 exlat:1200 rrt:3 rrl:3 rwt:3 rwl:3 idle_power:- active_power:- ps 4 : mp:0.0050W non-operational enlat:2000 exlat:8000 rrt:4 rrl:4 rwt:4 rwl:4 idle_power:- active_power:-
-
RE: Error Restoring GPT Partition Tables
@george1421 No worries. Just making sure there wasn’t something you knew that I didn’t
-
RE: Error Restoring GPT Partition Tables
@george1421 Sure. I understand about narrowing down the possibilities. I can switch one of these to legacy and see what happens with the drives. To be clear, these are HP workstations with Samsung NVME M.2 drives. Are either of those companies related to Lenovo in some way?