Posts made by rlindenschmidt

Hi all. Been using FOG for like two years with zero problems until today. Trying to generate a new image for a computer lab and am unable to complete the task. Initially I didn’t catch the error as FOG has been set it and forget it for me. This occurs when I am generating the initial image:

Reading Partition Tables…ldm_parse_tocblock can’t find TOCBLOCK, database may be corrupt

The resulting image fails to apply to the target machine with the following error:

Target partition size (2MB) is smaller than source (1075MB).

Are these two things even related?

The image I’m generating has four partitions, is Windows 7, and usually clones without a problem.

Thanks for any insight, I’m going nuts over here.

Error in the server config file. Thanks for the pointer, happily cloning away!

I migrated to a new server, fresh 1.4.4 install. I imaged 3 or so laptops with an image I had prior to the migration that I imported with no problems. I then realized I needed to update a few things in the image, so I did and then attempted to capture the image. Everything works fine right until the very end with an FTP login error. I’ve updated the user in the FOG server, made sure the management username/pass is correct in storage management, and even checked the TFTP login/pass in settings. What am I missing? Attached is the error shot.

Sorry for the delay, had a snow day yesterday and didn’t wanna come in just for this. Wound up deleting the default storage node and recreating it. Rebooted, and now everything seems to be good.

@tom-elliott If the storage ID is the same as the name, same error. if the ID is something else, unsure where to locate that.

@tom-elliott If I actually try to edit the node, my IP and all info shows up.

@george1421 and Here you go. Thanks for the assistance!

@george1421 Yes, it is a single fog server. The storage is a partition on the (only) hard drive. Here’s the output:

Filesystem Size Used Avail Use% Mounted on
devtmpfs 3.9G 0 3.9G 0% /dev
tmpfs 3.9G 11M 3.9G 1% /dev/shm
tmpfs 3.9G 2.0M 3.9G 1% /run
tmpfs 3.9G 0 3.9G 0% /sys/fs/cgroup
/dev/sda2 49G 6.1G 41G 14% /
tmpfs 3.9G 2.2M 3.9G 1% /tmp
/dev/sda1 976M 142M 768M 16% /boot
/dev/sda3 9.8G 347M 9.0G 4% /home
/dev/sda6 383G 69M 364G 1% /images
tmpfs 788M 16K 788M 1% /run/user/42
tmpfs 788M 4.6M 783M 1% /run/user/1000

Just installed Fedora 27 on a machine, followed the recommendations on how to properly partition and mount points. Installed Fog 1.4.4 with no errors. Log in, and the dashboard reports no storage node space. Clicking on it goes to hardware information and it says Invalid Server Information. I click edit node > DefaultMember and everything looks good there. What am I missing or what went wrong on install?

Thanks, will do!

Uhm…maybe? I’d assume I did because I was prompted for a user/pass. I probably made things worse now by deleting the default node and recreating it. I’ll keep an eye out for that box. Thanks!

I’ve got my server up and running, created an image, and pushed it to another client. Truly awesome. I realized that I should have set some things first (I was excited). I deleted the old image in the GUI, but it still shows in the pie graph on the front page. Further, it’s still in /images on the server. What’s the correct method for getting rid of images you don’t need?

Server

• FOG Version: 1.4.2
• OS: Fedora 24

I forgot to mark my changes permanent across reboots. It’s chugging right along now. Thanks!

Server

• FOG Version: 1.4.2
• OS: Fedora 24

Description

After installing Fedora 24 and following the recommendations on the wiki, I found myself with a shiny new FOG server. My only problem is I cannot access the management console from any other box. I can ping it, but that’s it. Both localhost and the IP (10.100.0.16) get me to the console on the server. Please, be gentle. This is largely uncharted territory for me.