I just did another clean install of Ubuntu Desktop 13.10, with FOG 1.1.2. I made sure that I did not set a MYSQL password.
I still cannot multicast.

[07-16-14 4:59:22 pm] * No tasks found!
[07-16-14 4:59:32 pm] | Task (1) Multi is new!
[07-16-14 4:59:32 pm] | Task (1) /images/163QAIfinalRev5 image file found.
[07-16-14 4:59:32 pm] | Task (1) 3 client(s) found.
[07-16-14 4:59:32 pm] | Task (1) Multi sending on base port: 63100
[07-16-14 4:59:32 pm] CMD: cat “/images/163QAIfinalRev5”|/usr/local/sbin/udp-sender --min-receivers 3 --portbase 63100 --interface eth0 --full-duplex --ttl 32 --nokbd;
[07-16-14 4:59:32 pm] | Task (1) Multi has started.
[07-16-14 4:59:42 pm] | Task (1) Multi is no longer running.
[07-16-14 4:59:52 pm] | Task (1) Multi is no longer running.

I have deleted the items from the table and restarted the services and nada.
I can single download and upload without issue.

Have you tried to reinstalling Ubuntu? I have not seen a Kernel Panic using FOG before, but I have had a bad install of Ubuntu for no reason.

I have a clean install of FOG on Ubuntu 13.10.
I’m having the same issue. Hanging on the Partclone screen.
Unicast is working

Network is very basic.
FOG Server -> unmanaged switch -> PC’s

There is nothing special about the setup.

I start the Multicast and the session seems to end right away. I have rebooted the server and restarted the services indicated earlier in this post.

Here is the dump from my log.

[07-11-14 3:49:46 pm] * No tasks found!
[07-11-14 3:49:56 pm] | Task (8) Multitest is new!
[07-11-14 3:49:56 pm] | Task (8) /images/163DS image file found.
[07-11-14 3:49:56 pm] | Task (8) 3 client(s) found.
[07-11-14 3:49:56 pm] | Task (8) Multitest sending on base port: 53574
[07-11-14 3:49:56 pm] CMD: cat “/images/163DS”|/usr/local/sbin/udp-sender --min$
[07-11-14 3:49:56 pm] | Task (8) Multitest has started.
[07-11-14 3:50:06 pm] | Task (8) Multitest is no longer running.

I re-uploaded the image as a Single Disk (NTFS Only). and now I can download the image to similar hardware.

Hello,
I have just installed FOG and am trying to figure my way around.
I have everything installed and “working”. I have a PC that has a Basic Image on (OS, drivers, updates ect) that I successfully registered as a host device and uploaded and image of.
I also successfully downloaded the same image back on to the same device no problem.

I have a 2nd device which is the exact same hardware. I successfully registered the device (using Full the 1st time) and using the Web portal scheduled a download of the image I created off the first device. I assigned the new host to use the image I created of the 1st device.

FOG goes through the motions but does not actually download the image ( the screen goes by way to fast to see any error messages).
When I check the Task history, is simply reports success.
I have deleted the 2nd device as a host and tried repeating the steps using a quick image but FOG will not download the image.

What the heck am I doing wrong?