Hello
Working with dell PowerEdge R640,
I started get the following error: No configuration methods succeeded
please see attached picture.
My setup PowerEdge R640 , FOG 1.5.9 bzImage Version: 5.15.19 bzImage32 Version: 4.19.145

@george1421 I want to say thank you very much for your support and help.\It was very professional and fast, thanks again now I can continue enjoy a FOG solution in my environment

Best regards, Boris

@george1421 , ok I will try both options and update you with findings

Best regards,
Boris.

Hello @george1421

it working !!!
Thank you, please see the screenshot :

Please advice what is a next step ?

Best regards,
Boris.

@george1421 said in FOG cannot load qlogic network driver on PowerEdge R640:

est to see if you have an IP address w

Hello @george1421 i have followed your instructions please see an attached screenshot of what
I get:

Also adding dmes output:

@george1421 said in FOG cannot load qlogic network driver on PowerEdge R640:

t and told me that there is missing firmware too. That saved us a second t

Thank you a lot for help and support

Hello @george1421
thank you for the fast response.

I cannot do ssh since I cannot set IP address in debug mode (i guess luck of drivers).
I do have screenshot of consol, hope its help:

Best regards,
Boris.

@george1421 said in FOG cannot load qlogic network driver on PowerEdge R640:

lspci -nn | grep -i raid

Hello, @george1421 first of all thank you for the replay, second sorry for the delay with my answer.
The problem is that i cannot load/run Inventory in order to register the dell in the FOG database as a host.

I can send you output lspci output from standard centos hope it can help us

I install centos on dell server and run following command:

lspci -nn | grep -i net

18:00.0 Ethernet controller [0200]: QLogic Corp. FastLinQ QL41000 Series 10/25/40/50GbE Controller [1077:8070] (rev 02)
18:00.1 Ethernet controller [0200]: QLogic Corp. FastLinQ QL41000 Series 10/25/40/50GbE Controller [1077:8070] (rev 02)


lspci -nn | grep -i raid
86:00.0 RAID bus controller [0104]: Broadcom / LSI MegaRAID SAS-3 3108 [Invader] [1000:005d] (rev 02)

 lspci -s 18:00.0 -vvv
18:00.0 Ethernet controller: QLogic Corp. FastLinQ QL41000 Series 10/25/40/50GbE Controller (rev 02)
        Subsystem: QLogic Corp. Device 000c
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 113
        NUMA node: 0
        Region 0: Memory at 9e820000 (64-bit, prefetchable) [size=128K]
        Region 2: Memory at 9e000000 (64-bit, prefetchable) [size=8M]
        Region 4: Memory at 9e850000 (64-bit, prefetchable) [size=64K]
        Expansion ROM at 9ea00000 [disabled] [size=512K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable- Count=1/8 Maskable+ 64bit+
                Address: 0000000000000000  Data: 0000
                Masking: 00000000  Pending: 00000000
        Capabilities: [70] Express (v2) Endpoint, MSI 00
                DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
                        RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset-
                        MaxPayload 256 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 8GT/s, Width x8, ASPM not supported, Exit Latency L0s unlimited, L1 <8us
                        ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 8GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
                DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Via message/WAKE#
                DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled
                LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
                         Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
                         Compliance De-emphasis: -6dB
                LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete+, EqualizationPhase1+
                         EqualizationPhase2+, EqualizationPhase3+, LinkEqualizationRequest-
        Capabilities: [b0] MSI-X: Enable+ Count=129 Masked-
                Vector table: BAR=4 offset=00000000
                PBA: BAR=4 offset=00001000
        Capabilities: [d0] Vital Product Data
                Product Name: QLogic 2x25GE QL41262HMCU CNA
                Read-only fields:
                        [PN] Part number: QL41262HMCU-DE
                        [SN] Serial number: REE1812B33318
                        [MN] Manufacture ID: 31 30 32 38
                        [V0] Vendor specific: FFV15.20.16
                        [V1] Vendor specific: DSV1028VPDR.VER2.1
                        [V2] Vendor specific: NPY2
                        [V3] Vendor specific: PMTD
                        [V4] Vendor specific: NMVQLogic
                        [V5] Vendor specific: DTINIC
                        [V6] Vendor specific: DCM1001FFFFFF1202FFFFFF1403FFFFFF1604FFFFFF1805FFFFFF1A06FFFFFF1C07FFFFFF1E08FFFFFF2101FFFFFF2302FFFFFF2503FFFFFF2704FFFFFF2905FFFFFF2B06FFFFFF2D07FFFFFF2F08FFFFFF
                        [V9] Vendor specific: 15.20.13
                        [RV] Reserved: checksum good, 5 byte(s) reserved
                End
        Capabilities: [100 v2] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt+ UnxCmplt- RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap+ CGenEn+ ChkCap+ ChkEn+
        Capabilities: [148 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
                        Status: NegoPending- InProgress-
        Capabilities: [168 v1] Device Serial Number 00-00-00-00-00-00-00-00
        Capabilities: [178 v1] Power Budgeting <?>
        Capabilities: [188 v1] Alternative Routing-ID Interpretation (ARI)
                ARICap: MFVC- ACS-, Next Function: 1
                ARICtl: MFVC- ACS-, Function Group: 0
        Capabilities: [198 v1] #19
        Capabilities: [1f8 v1] Transaction Processing Hints
                Interrupt vector mode supported
                Device specific mode supported
                Steering table in MSI-X table
        Capabilities: [284 v1] Latency Tolerance Reporting
                Max snoop latency: 0ns
                Max no snoop latency: 0ns
        Capabilities: [28c v1] Vendor Specific Information: ID=0002 Rev=3 Len=100 <?>
        Capabilities: [38c v1] Vendor Specific Information: ID=0001 Rev=1 Len=038 <?>
        Capabilities: [3c4 v1] Precision Time Measurement
                PTMCap: Requester:+ Responder:- Root:-
                PTMClockGranularity: Unimplemented
                PTMControl: Enabled:- RootSelected:-
                PTMEffectiveGranularity: Unknown
        Capabilities: [3d0 v1] Vendor Specific Information: ID=0003 Rev=1 Len=054 <?>
        Capabilities: [424 v1] #15
        Kernel driver in use: qede
        Kernel modules: qede

Greetings
I have a problem loading and running FOG od dell server model PowerEdge R740
with Integrated NIC 1, QLogic 2x25GE QL41262HMKR.

I got the error no driver found.

I do update the latest fog kernel but the error existing

Please advise how to solve it.

Best regards,

Hello.
I have FOG installed on VM with the latest versions:
bzImage Version: 5.15.19
bzImage32 Version: 4.19.145

When I boot PowerEdge R640 server from FOG, and go to inventory I got an error
No network interfaces found, your kernel probably missing the correct driver
see the attachment below:

PowerEdge R640 HW details from iDRAC
Integrated NIC 1: QLogic 2x25GE QL41262HMCU CNA
Family Firmware Version 14.05.00
Family Driver Version 8.37.0.20

Supported Boot Protocol iSCSI, PXE, FCoE

Please advise how I can fix this issue.