Image does not upload!
-
Yeah, I’m not sure about the multiple chkdsk thing either. I have been told to do it though by the developers before, so I just run it twice now.
The BIOS setting sounds OK. I was worried about RAID. Dells seems to come with RAID turned on and I’ve had problems with that.
The mysql password is not an issue. It is fine to create that as long as you make sure you configure fog to use the password. I actually set a password for mysql. Think of it this way, if you can see any information about hosts or images, etc in the web gui, fog knows your mysql password because it is pulling all that info from mysql tables.
I’ll try to create a 3.4.5 kernel in the morning and post the link to this thread. Just “watch” this thread so you get a notice when it is posted.
astrouga -
[quote=“don miyagi, post: 4878, member: 1564”]I’ve been able to upload images from two other computers and I’m 99.9% sure it has to do with the nic drivers and the kernel. Is there a way I can include certain nic drivers? Do I have to create a custom kernel? Is there such a thing as a definitive guide to that process?
[/quote]I’ve commited myself to making a 3.4.5 kernel tomorrow, so I’ll post a note when I’ve got something working.
astrouga
-
[quote=“astrouga, post: 4883, member: 907”]I’ve commited myself to making a 3.4.5 kernel tomorrow, so I’ll post a note when I’ve got something working.
astrouga[/quote]
Thanks a lot for all of your help. I went ahead and installed 10.4 LTS on one of many hp dx7500 I have to see what module it uses for the network adapter. I ran the following command in terminal: lshw -C networking
*-network
description: Ethernet interface
product: 82567V-2 Gigabit Network Connection
vendor: Intel Corporation
physical id: 19
bus info: pci@0000:00:19.0
logical name: eth0
version: 00
serial: xx:xx:xx:xx:xx:xx
size: 1GB/s
capacity: 1GB/s
width: 32 bits
clock: 33MHz
capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.0.2-k2 duplex=full firmware=1.8-5 ip=192.168.x.x latency=0 link=yes multicast=yes port=twisted pair speed=1GB/s
resources: irq:26 memory:feac0000-feadffff memory:feafe000-feafefff ioport:d000(size=32)I haven’t tried creating the custom kernel at this point. I have remastersys loaded on my system. Should I do a backup of the system or should a backup of the current fog kernel be sufficient?
-
I just realized I posted in the wrong section. I hope I don’t get any lashings. Sorry everyone.
-
Lashings! and with a wet noodle too!
-
[quote=“don miyagi, post: 4900, member: 1564”]Thanks a lot for all of your help. I went ahead and installed 10.4 LTS on one of many hp dx7500 I have to see what module it uses for the network adapter. I ran the following command in terminal: lshw -C networking
I haven’t tried creating the custom kernel at this point. I have remastersys loaded on my system. Should I do a backup of the system or should a backup of the current fog kernel be sufficient?[/quote]
I’m not sure what you are asking here. You don’t need to worry about where you build the kernel. You don’t have to mess around with your existing fog kernel, unless you want all of your systems to use the new one. Then you could just:
“mv bzImage bzImage.default”
Then you could just move your new kernel over to that directory and test it out.–astrouga.
-
Ok. I ended up answering my own question as I delved more into creating a custom kernel. I followed the guide exactly and removed all network drivers except the Intel drivers. We’ll see what happens soon.
Some more interesting information:
I’m able to do all the advanced deployments in task management on the dx 7500 systems.
When I check FOG compatibility it says it is [OK]
I’ve tried uploading an image of ubuntu and it completes in a matter of milliseconds and says that it has completed successfully, however, when i try and download the image it fails. -
Fog cannot image ext4 fs partitions currently. So if your Ubuntu image you are trying to upload was not specifically setup to be ext3, then you won’t be able to upload/deploy.
-
[quote=“astrouga, post: 4883, member: 907”]I’ve commited myself to making a 3.4.5 kernel tomorrow, so I’ll post a note when I’ve got something working.
astrouga[/quote]
Any luck with a 3.4.5 Kernel?My custom kernel did not work with the dx7500’s and I was really hoping to get FOG working in my environment. I love GNU/Linux and open source, but my boss set a timeline for me to get this functional. My time is running out. Luckily, he is out of the office today but he has mentioned that I need to move on to plan B which is a trial of the Dell Kace K2000. The community here is awesome and I’m thankful for the time you guys have taken to post to my thread. I may revisit this option in the future, but for now, alas! I was not able to win this battle. Sorry gents…
-
Sorry, I got swamped then forgot. I just created this one using the 3.4.5 kernel. I haven’t tested it, so I can’t guarantee it will work. I’ll try to take a look later to make sure I didn’t miss anything. Let me know if it works at all.
[url]http://www.filedropper.com/bzimage34_1[/url]
astrouga