Hosts Sharing USB NIC

[it101]

Well I am trying to update and keep getting to Installing php-gettext…Failed.

I found a thread with something similar but it doesnt help. The thread said to run these commands

sudo apt-get autoremove --purge
sudo rm -rf /etc/php5
sudo rm -rf /etc/apt-get/sources.d/ondrej
sudo apt-get purge php5*
sudo apt-get autoremove --purge

But the install still fails.

[Wayne Workman]

@it101 Try to install gettext beforehand, and then try the installer again.
sudo apt-get install gettext

[Wayne Workman]

Also, what’s the error when you try it manually?
sudo apt-get install php-gettext

[it101]

This post is deleted!

[it101]

This is what I get.

sudo apt-get install php-gettext
Reading package lists... Done
Building dependency tree
Reading state information... Done
php-gettext is already the newest version.
You might want to run 'apt-get -f install' to correct these:
The following packages have unmet dependencies:
 libapache2-mod-php5 : Depends: apache2-mpm-prefork (> 2.0.52) but it is not going to be installed or
                                apache2-mpm-itk but it is not going to be installed
                       Depends: apache2.2-common but it is not going to be installed
E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution).

I think I’m just going to backup my images and install a fresh 14.4 LTS and FOG 1.3

[Tom Elliott]

@it101 The instructions you followed weren’t followed properly, from what I can see.

You should’ve ran:

rm -rf /etc/{apache,php}*
rm -rf /etc/apt-get/sources.d/ondrej
apt-get purge apache2* php5* php7*
apt-get autoremove --purge

Notice you must add apache to the list.

Also, the RC-25 should properly handle this installation and changes required properly.

[Wayne Workman]

@it101 said in Hosts Sharing USB NIC:

I think I’m just going to backup my images and install a fresh 14.4 LTS and FOG 1.3

I would urge you to use Ubuntu 16.04 - it is Canonical’s current long-term-support version of Ubuntu and FOG 1.3.0 installs and runs perfectly fine on it.

[it101]

@Tom-Elliott I ran those commands too and the update fails at the same spot of installing php-gettext, I tried manually installing php-gettext and get the same error as above.

@Wayne-Workman The only reason I said 14.4 LTS is because the wiki says 16 has issues. But with your blessing, I will use 16 LTS.

[Wayne Workman]

@it101 16 doesn’t have issues anymore (Tom fixed them). What wiki article were you looking at?

[Tom Elliott]

@it101 What version of FOG are you installing? (SVN, GIT, tarball?)

[it101]

@Wayne-Workman I was looking at This

@Tom-Elliott I am using GIT

[Wayne Workman]

@it101 Fixed.

[it101]

@Wayne-Workman Can I just install FOG 1.3 on Ubuntu 16 or do I need to install 1.2 first then upgrade to 1.3?

[Wayne Workman]

@it101 You don’t need to touch 1.2.0 at all, you can go straight to 1.3 using the “Upgrade to Trunk” article, or the “Ubuntu 16.04 Server” article in the wiki. Or, if you just know the commands, you don’t need any instructions. But no you don’t need to mess with 1.2.0 at all. People keep asking that here in the forums and I don’t know why. Is there anything indicating that 1.2.0 is needed? Please point out why you feel that way and I’ll do what I can to change it.

[it101]

@Wayne-Workman I tried installing 1.3 on Ubuntu 16 one time without installing 1.2 first and it didnt ask me about changing the SQL password but did ask if the password was blank. I said yes and it installed without a hitch. But when I went to capture my first image, it couldnt mount the file system and fails immediately

Also, I think some might be taking the “Upgrade to Trunk” at face value thinking it is JUST an upgrade and not a full install.

[Wayne Workman]

@it101 said in Hosts Sharing USB NIC:

Also, I think some might be taking the “Upgrade to Trunk” at face value thinking it is JUST an upgrade and not a full install.

I’ll clarify this at the very top of the article, then.

when I went to capture my first image, it couldnt mount the file system and fails immediately

Exactly where does this happen? Please post a photo of the error, and if you can please also post a photo what the screen is showing just before the error as well. This will let us know exactly where the issue is.

[it101]

@Wayne-Workman I just tried installing 1.3 on Ubuntu 16 Server and during the install, it fails at

Starting FOGMulticastManager Service ................. Failed!

Is this anything to be alarmed at? Proceed as normal?

The only reason I am using Ubuntu is because I am somewhat familiar with it (not saying much) should I try Debian?

[Wayne Workman]

@it101 Give me 5 minutes to test the latest on Ubuntu 16 here. I’m home today and have lots of time on my hands.

[it101]

@Wayne-Workman OK, so I ran the 1.3 install again after the FOGMulticastManager Service Failed message and it completed successfully.

BUT, when I got to capture my image, I get to “Saving original partition table…” and stops there. No error or anything.

[Wayne Workman]

I know you’re new to fog so you’re going to have a ton of questions. We are happy to help but us going so far off topic here benefits nobody but you. We use forums so others can search threads and help themselves instead of asking questions. Please for each “new” issue, make a new thread.

When the capture process hangs on “Saving original partitions” this means that you have a system that shipped from the factory as UEFI, and you’ve changed it to BIOS and reformatted it, but because windows installation does a crappy job of cleaning up the disk, there are GPT remnants left over, and you need to run ‘fixparts’ in debug mode. Search the forums for fixparts and you’ll find numerous writeups on how to do it. That’ll fix you up. You could also search for the exact last lines displayed and find the same things.

Also there is this:
https://wiki.fogproject.org/wiki/index.php?title=Troubleshoot_Capturing