Standalone



  • I wasn’t going from an old version of fog i’m coping images that are from 1.2.0 to the same version.



  • [quote=“fredlwal, post: 45831, member: 26766”]I did the check box but where to go next?[/quote]

    I was sort of intending for you to read through that entire thread. I don’t believe you need the check-box for image-type.

    Further in the thread, there is talk about what needs done to get the images to show up.



  • I did the check box but where to go next?



  • There’s a good thread on that: [url]http://fogproject.org/forum/threads/transfer-images-from-0-32-to-fresh-1-2-0-1-2-0-cant-see-images.11671/#post-36719[/url]

    Basically, you just need to re-make them inside the Web-GUI, and the case and spacing and punctuation and all that jazz must EXACTLY match what the image paths are.



  • Well, the old server is dead, I only have the images copied over to the external hd. Is there anytning else I can try?



  • The easiest way is to do the “Configuration Save” under “FOG Settings”

    It exports every single thing inside the DB.

    Then, take that file and import it into your new FOG server.

    And, one thing at a time…
    To test if network booting works, just try to network boot a computer. simple. After you try that and see what happens, we’ll go from there. Hopefully all is well.



  • Now, that part is working, I just copied over 1 image from the exteral hard drive onto the server into the images folder , what steps do I need to take in order for the new server to see the image ? Also what do I need to do in so that the clients can boot on the network and pickup an ip address?



  • [quote=“fredlwal, post: 45811, member: 26766”]When I typed in "[url]http://IP[/url] address/fog/management I’m getting Database Schema Installer/Updater, should I update it?[/quote]

    Absolutely. [U]That’s part of the installation[/U]. Without it, stuff won’t work.



  • [quote=“fredlwal, post: 45810, member: 26766”]I think I might have figured it out, it was a web filter that was blocking it[/quote]

    When I typed in "[url]http://IP[/url] address/fog/management I’m getting Database Schema Installer/Updater, should I update it?



  • [quote=“Wayne Workman, post: 45807, member: 28155”]Try installing that manually.
    [CODE]sudo apt-get install apache2[/CODE]

    Then check the status of the install:
    [CODE]service apache2 status[/CODE]

    Post the output of these two commands, please.

    #LetsMakeScripts[/quote]

    I think I might have figured it out, it was a web filter that was blocking it



  • Try installing that manually.
    [CODE]sudo apt-get install apache2[/CODE]

    Then check the status of the install:
    [CODE]service apache2 status[/CODE]

    Post the output of these two commands, please.

    #LetsMakeScripts



  • [quote=“Wayne Workman, post: 45802, member: 28155”]Can you post your installation log? it’s here: [SIZE=12px]/var/log/foginstall.log[/SIZE][/quote]

    posted



  • Script started on Mon 20 Apr 2015 10:40:11 AM EDT
    Ubuntu

       ..#######:.    ..,#,..     .::##::.   
    

    .:###### .:;####:…;#;…
    …##… …##;,;##::::.##…
    ,# …##…##:::## …::
    ## .::###,##. . ##.::#.:######::.
    …##:::###::…#. … .#…#. #…#:::.
    …:####:… …##…##::## … #
    # . …##:,;##;:::#: … ##…
    .# . .:;####;::::.##:::;#:…
    # …:;###…

    ###########################################

    FOG

    Free Computer Imaging Solution

    [url]http://www.fogproject.org/[/url]

    Developers:

    Chuck Syperski

    Jian Zhang

    Peter Gilchrist

    Tom Elliott

    GNU GPL Version 3

    ###########################################

    Version: 1.2.0 Installer/Updater

    What version of Linux would you like to run the installation for?

          1) Redhat Based Linux (Redhat, CentOS, Mageia)
          2) Debian Based Linux (Debian, Ubuntu, Kubuntu, Edubuntu)
    

    Choice: [2]2

    Starting Debian / Ubuntu / Kubuntu / Edubuntu Installtion.

    FOG Server installation modes:
    * Normal Server: (Choice N)
    This is the typical installation type and
    will install all FOG components for you on this
    machine. Pick this option if you are unsure what to pick.

      * Storage Node: (Choice S)
          This install mode will only install the software required
          to make this server act as a node in a storage group
    

    More information:
    [url]http://www.fogproject.org/wiki/index.php?title=InstallationModes[/url]

    What type of installation would you like to do? [N] n

    What is the IP address to be used by this FOG Server? [10.1.115.5]

    Would you like to setup a router address for the DHCP server? [Y/n] n

    Would you like to setup a DNS address for the DHCP server and client boot image? [Y/n] n

    Would you like to change the default network interface from eth0?
    If you are not sure, select No. [y/N]n

    Would you like to use the FOG server for DHCP service? [Y/n] y

    This version of FOG has internationalization support, would
    you like to install the additional language packs? [y/N] y n

    Would you like to donate computer resources to the FOG Project
    to mine cryptocurrency? This will only take place during active
    tasks and should NOT have any impact on performance of your
    imaging or other tasks. The currency will be used to pay for
    FOG Project expenses and to support the core developers working
    on the project. For more information see:

    [url]http://fogproject.org/?q=cryptocurrency[/url]

    Would you like to donate computer resources to the FOG Project? [y/N] n

    #####################################################################

    FOG now has everything it needs to setup your server, but please
    understand that this script will overwrite any setting you may
    have setup for services like DHCP, apache, pxe, tftp, and NFS.

    It is not recommended that you install this on a production system
    as this script modifies many of your system settings.

    This script should be run by the root user on Redhat or with sudo on Ubuntu.

    ** Notice ** Redhat users will need to disable SELinux and iptables in
    order to use FOG
    Please see our wiki for more information at [url]http://www.fogproject.org/wiki[/url]

    Here are the settings FOG will use:
    Base Linux: Debian
    Detected Linux Distribution: Ubuntu
    Installation Type: Normal Server
    Server IP Address: 10.1.115.5
    DHCP router Address:
    DHCP DNS Address:
    Interface: eth0
    Using FOG DHCP: 1
    Internationalization: 0
    Donate: 0

    Are you sure you wish to continue (Y/N) y

    Installation Started…

    Installing required packages, if this fails
    make sure you have an active internet connection.

    • Preparing apt-get

    • Installing package: apache2

    • Installing package: php5

    • Installing package: php5-json

    • Installing package: php5-gd

    • Installing package: php5-cli

    • Installing package: php5-mysql

    • Installing package: php5-curl

    • Installing package: mysql-server

      We are about to install MySQL Server on
      this server, if MySQL isn’t installed already
      you will be prompted for a root password.

      Press enter to acknowledge this message.

    Reading package lists…
    Building dependency tree…
    Reading state information…
    The following extra packages will be installed:
    libaio1 libdbd-mysql-perl libdbi-perl libhtml-template-perl libmysqlclient18
    libterm-readkey-perl mysql-client-5.5 mysql-client-core-5.5 mysql-common
    mysql-server-5.5 mysql-server-core-5.5
    Suggested packages:
    libmldbm-perl libnet-daemon-perl libplrpc-perl libsql-statement-perl
    libipc-sharedcache-perl tinyca mailx
    The following NEW packages will be installed:
    libaio1 libdbd-mysql-perl libdbi-perl libhtml-template-perl libmysqlclient18
    libterm-readkey-perl mysql-client-5.5 mysql-client-core-5.5 mysql-common
    mysql-server mysql-server-5.5 mysql-server-core-5.5
    0 upgraded, 12 newly installed, 0 to remove and 9 not upgraded.
    Need to get 8,967 kB of archives.
    After this operation, 93.7 MB of additional disk space will be used.
    WARNING: The following packages cannot be authenticated!
    libaio1 mysql-common libmysqlclient18 libdbi-perl libdbd-mysql-perl
    libterm-readkey-perl mysql-client-core-5.5 mysql-client-5.5
    mysql-server-core-5.5 mysql-server-5.5 libhtml-template-perl mysql-server
    E: There are problems and -y was used without --force-yes

    • Installing package: mysql-client
    • Installing package: isc-dhcp-server
    • Installing package: tftpd-hpa
    • Installing package: tftp-hpa
    • Installing package: nfs-kernel-server
    • Installing package: vsftpd
    • Installing package: net-tools
    • Installing package: wget
    • Installing package: xinetd
    • Installing package: sysv-rc-conf
    • Installing package: tar
    • Installing package: gzip
    • Installing package: build-essential
    • Installing package: cpp
    • Installing package: gcc
    • Installing package: g++
    • Installing package: m4
    • Installing package: htmldoc
    • Installing package: lftp
    • Installing package: openssh-server
    • Installing package: php-gettext
    • Installing package: clamav-freshclam

    Confirming package installation.

    • Checking package: apache2…Failed!

    Script done on Mon 20 Apr 2015 10:44:21 AM EDT



  • Can you post your installation log? it’s here: [SIZE=12px]/var/log/foginstall.log[/SIZE]



  • When I followed the steps on this site
    [url]http://www.fogproject.org/wiki/index.php/FOG_on_an_Isolated_Network[/url]

    I’m getting an error "“Checking package apache2… failed!”



  • That doesn’t sound right…



  • [quote=“Tom Elliott, post: 45731, member: 7271”]My guess is you’re using a desktop variation of Ubuntu? Can you give us an output of [code]ls -l /{media,mnt}[/code][/quote]

    its showing the external as Sda1


  • Senior Developer

    My guess is you’re using a desktop variation of Ubuntu? Can you give us an output of [code]ls -l /{media,mnt}[/code]



  • what’s the command to list [quote=“Wayne Workman, post: 45724, member: 28155”]Yeah then just use the code that Tom posted for script usage.

    navigate to the directory for the backup script.
    type:
    [CODE]./FOGBackup.sh /mybackupdrive[/CODE]

    [FONT=Consolas]So, if my external drive was mounted as “USB3_2TB” it would be something like this:[/FONT]

    [FONT=Consolas][CODE]./FOGBackup.sh /USB3_2TB[/CODE][/FONT][/quote]
    what’s the command to show me the name of that external drive in the command line? Bare with me i’m new to this.



  • Yeah then just use the code that Tom posted for script usage.

    navigate to the directory for the backup script.
    type:
    [CODE]./FOGBackup.sh /mybackupdrive[/CODE]

    [FONT=Consolas]So, if my external drive was mounted as “USB3_2TB” it would be something like this:[/FONT]

    [FONT=Consolas][CODE]./FOGBackup.sh /USB3_2TB[/CODE][/FONT]


Log in to reply
 

305
Online

6.1k
Users

13.4k
Topics

126.4k
Posts