Fog registration with NUC
-
Loss of data?
What do you mean?
-
[FONT=sans-serif][COLOR=#000000][B]NOTE: 1.0.0 is a, nearly, complete rewrite from previous versions of FOG. There may be issues when upgrading from past revisions of FOG so please backup you installation before upgrading![/B][/COLOR][/FONT]
[FONT=sans-serif][COLOR=#000000]Migration for 0.32 to version 1.x.x will cause you to loose the operation system information that was associated with your hosts. This information has been moved to the image item now, so you will need to update all your images to set the appropriate operating system! Please see the Migration Instructions section below for more information.[/COLOR][/FONT]
[FONT=sans-serif][COLOR=#000000]All commands are assumed to be run as root. If you don’t have access to root, prepend the installation with sudo (ex.[/COLOR][/FONT]
[FONT=sans-serif][COLOR=#000000] [/COLOR][/FONT]
[FONT=sans-serif][COLOR=#000000]from [url]http://fogproject.org/wiki/index.php?title=Upgrade_to_1.0.0[/url][/COLOR][/FONT] -
what that’s talking about is not a “risk.” It’s a change in operating procedure. Before, OS was associated with hosts. but the actual operating system resides in the image. so, that’s where that info has been put now.
you should, of course, be prepared for a catastrophic failure, as you should be at all times, and especially when performing a major upgrade. We recommend that you do a fresh install instead of an upgrade, and migrate your data over to the new server. that is because you’re much less likely to have issues that way. upgrading is, however, supported. -
Update: I have built a new UBUNTU desktop 14.04lts and have installed FOG 1.1.2 and I am to this point from the instructions on Building UNDIONLY.KPXE file (see link above) and I do not understand the “[B][FONT=sans-serif][COLOR=#000000]Remove the {}'s and only apply the file you wish to build if you want only a specific file.” from this part.[/COLOR][/FONT][/B]
[FONT=sans-serif][COLOR=#000000]Build the undionly/ipxe files.[/COLOR][/FONT]
[FONT=sans-serif][COLOR=#000000][B]I USE THE FOLLOWING COMMAND TO BUILD ALL FILES AT ONCE.[/B] [B]Remove the {}'s and only apply the file you wish to build if you want only a specific file.[/B][/COLOR][/FONT]
[COLOR=#000000][FONT=monospace]make bin/{undionly,ipxe}.{,k,kk}pxe EMBED=ipxescript[/FONT][/COLOR]
[SIZE=5][B][FONT=sans-serif][SIZE=19px][COLOR=#000000]Copy and/or Use your files[/COLOR][/SIZE][/FONT][/B][/SIZE][FONT=sans-serif][COLOR=#000000][B]I USE THE FOLLOWING COMMAND TO COPY ALL FILES AT ONCE. Remove the {}'s and only copy the file you wish to use if you want only a specific file.[/B][/COLOR][/FONT]
[COLOR=#000000][FONT=monospace]cp bin/{undionly,ipxe}.{,k,kk}pxe /tftpboot/ [/FONT][/COLOR]
[COLOR=#000000][FONT=monospace]I ran the full command - make bin/{undionly,ipxe}.{,k,kk}pxe EMBED=ipxescript then realized it said to REMOVE the brackets should it be re-run but as[/FONT][/COLOR]
[FONT=monospace]make bin/undionly,ipxe.,k,kk pxe EMBED=ipxescript[/FONT]
[COLOR=#000000][FONT=monospace][/FONT][/COLOR]
[COLOR=#000000][FONT=monospace][/FONT][/COLOR] -
why are you building unidonly.kpxe? one is included with fog, that has fog-specific embedded scripting
-
because when I went to do this, it said it did not exist.
[FONT=Consolas]cd /tftpboot
mv undionly.kpxe undionly.kpxe.ORIGINAL
ln -s undionly.kkpxe undionly.kpxe[/FONT] -
So you’re still running 0.32?
-
if you installed FOG 1.1.2, you should no longer have the problem where the undionly.kpxe, or undionly.kkpxe do NOT exist.
-
even if the files were for some reason missing, you could just download them from the sourceforge page
-
could this be a rights issue? When I use the file browser I can see the tftpboot folder, but can’t get access to it.
Tom - this was a brand new install of FOG 1.1.2 on a new Ubuntu 14.04LTS desktop. So when I did’t see the tftpboot folder, I assumed that I had to create the UNDIONLY files and stared following those directions.
-
when you ran the installer, did you run it with sudo?
-
yes, did sudo ./installfog.sh
-
What’s the contents of your /var/log/installfog.log file?
-
here is the file
[url=“/_imported_xf_attachments/1/1099_FOG LOGtext.txt?:”]FOG LOGtext.txt[/url]
-
So it looks like it never got past Mysql password setting. There’s nothing after this point which tells me 1.1.2 is not fully installed.
-
when you ran the installer, did you follow the instructions and prompts in the script?
-
Am a noob to Linux and fog but e may of had a similar experience when I did a fresh install today the first time trying to install MySQL wouldn’t it never prompted were it normally would for the root password to be set I had to rerun the installer second time it worked fine.
Ps it’s not anything to do with that he’s installed on Ubuntu 14.04 I saw a warning in the wiki that it’s too new and doesn’t work properly and was recommended in my thread on general to use 12.04.4
-
I re-ran the FOG install - here is the log file.
Still will not pxe boot a client.[url=“/_imported_xf_attachments/1/1100_FOG LOGtext2.txt?:”]FOG LOGtext2.txt[/url]
-
Is the dhcp option filename/67 pointing at undionly.kpxe or pxelinux.0?
Is the dhcp option next-server/66 pointing at the ip of your fog server?
-
I will have to check - headed home for the holiday weekend, Jared will pick this back up on Monday. Are those settings in the dhcpd file?
