Unable to boot correctly - Invalid OS ID
-
There is either something wrong with your site or my computer because when I type in this: [url]https://www.mastacontrola.com/[/url] it says the site is unavailable. I’ve tried in Firefox Chrome, and IE both at home and at work. Now I’d noticed earlier that Chrome did not like your SSL certificate so perhaps that is the issue?
I will check the image later and see if I can set the type there. However it sounds like the best course of action for both of use might be for me to pop the old hard drive back in (it still boots) and reimage it). My only concern is that if I do so, will there be any issues with corrupted files or errors being replicated between drives? I was getting a lot of event ID 153s before purchasing a new drive.
-
Lose the www part of the address
[url]https://mastacontrola.com[/url] -
Also, if at all possible, try running a full chkdisk from windows before setting up the upload task.
-
Ah that worked. Out of curiosity why does including the WWW produce an error?
I will run chkdsk again just to be sure. The last time it did not seem to do much but it’s best to be cautious where images are concerned. Also will it help to run the FOG installer on your website on my server or is it the same as the one I have? I noticed that different builds seem to have been released over the last few months and want to make sure mine is the one which will function best.
-
Because I use Dyndns to translate back to my home pc. I didn’t add webhop for www to translate back.
-
All should install pretty much the same. I’ve made some, but not many, changes to the installer, and I’ve tested them quite thouroughly so you should be good.
-
Changing the OS ID to Windows 8 for the image allowed me to boot into the menu. I like that the password is the same as for the web interface. And the new FOG menu is a little better than the old one in my opinion. But as you said, Tom, the image download did not work so over the weekend I will re-image my old hard drive and attempt this again.
-
Well partclone failed with the error “this disk has bad sectors”. That was on the first partition and the rest would not image at all. CHKDSK seems to have done nothing. Unless anyone has any other ideas this is probably the end of the line for this solution since I deleted the other image owing to my server not having enough space for both. Fortunately there was nothing on my laptop which was not elsewhere.
One question though. Partclone seemed to think my old hard drive was completely full when it wasn’t. Also it went extremely slowly before failing. Was that a bug or simply a function of the way the program operates?
-
Probably the way the program functions. It couldn’t obtain, (just my guess) the proper blkid because of the drive failing.
So it was probably trying to image using RAW format. The raw part worked until it couldn’t read the sector’s an further.
-
Ah ok. So on an ordinary day speeds will be comparable to what .32 can do? My initial concern was that partclone was slower than partimage.
Thank you for your help, but it looks like my hard drive is too far gone to be copied again. Probably I should not have deleted the old image. But I did get a chance to try out .33b without messing with one of the work computers.
-
[quote=“MikeoftheLibrary, post: 23398, member: 20568”]Ah ok. So on an ordinary day speeds will be comparable to what .32 can do? My initial concern was that partclone was slower than partimage.[/quote]
Yes 0.33b will be just as fast, if not FASTER than 0.32.
Tom is currently working on the iPXE system and I believe with it comes HTTP which is a hell of a lot faster than the FTP method we are currently using.
Tom even took the time to add in the ability to change the image compression and this in turn should help with both upload and download speed.
Sorry you are having issues with your drive. I actually set up a second box for my 0.33b, because 0.33b isn’t a direct drop in replacement for 0.32.
This way I still have my old images on my 0.32 server and I can start pushing my new images to BOTH until 0.33b is actively ready for my environment. Right now I have it separate from my network so I can test it and ti capabilities.
-
I look forward to using the new version in the future. It sounds like it will be vastly superior to .32.
The problems with my drive are largely due to the fact that it’s an advanced format drive. Even the Windows 8 recovery partition won’t work because it was created on a non-AFD disk. Also my laptop is 64-bit but my desktop is 32-bit so I can’t simply create an install disk from the windows 8 installer. Ugh!
FOG, however, has performed very well. This little adventure has helped me test out version .33b so when we do upgrade I the server at work I know what to expect. At present my plan is to wait until it’s finalized. Since we have about four spare computers (and only need about that many images) at work recreating reference images is not much of an issue. My main concern is for the FOG database since rebuilding it would require going around to the public computers. Is it possible to copy the database, store it somewhere, and then put it back on the server when version .33 is installed? Or is the best way to upgrade simply to have two servers? Note that we do not have any FOG server as of yet, although I do not want our big Windows 7 roll out to be dependent on software which is still in Beta.