• Hello,

    when I load an 1.3GB ISO over pxe it takes very long … around 15min.

    But I have a 5GBit Link. A iPerf3 speed test show me to the fog server:

    Connecting to host, port 5201
    [  4] local port 63421 connected to port 5201
    [ ID] Interval           Transfer     Bandwidth
    [  4]   0.00-1.00   sec   120 MBytes  1.01 Gbits/sec
    [  4]   1.00-2.01   sec  22.8 MBytes   189 Mbits/sec
    [  4]   2.01-3.00   sec   109 MBytes   918 Mbits/sec
    [  4]   3.00-4.00   sec   144 MBytes  1.21 Gbits/sec
    [  4]   4.00-5.00   sec   149 MBytes  1.25 Gbits/sec
    [  4]   5.00-6.00   sec   140 MBytes  1.17 Gbits/sec
    [  4]   6.00-7.00   sec   170 MBytes  1.42 Gbits/sec
    [  4]   7.00-8.00   sec   175 MBytes  1.47 Gbits/sec
    [  4]   8.00-9.00   sec   159 MBytes  1.34 Gbits/sec
    [  4]   9.00-10.00  sec   144 MBytes  1.21 Gbits/sec
    - - - - - - - - - - - - - - - - - - - - - - - - -
    [ ID] Interval           Transfer     Bandwidth
    [  4]   0.00-10.00  sec  1.30 GBytes  1.12 Gbits/sec                  sender
    [  4]   0.00-10.00  sec  1.30 GBytes  1.12 Gbits/sec                  receiver

    So around 1.12Gbits … way takes to load the ISO over TFTP so long?

    Thank you!

  • Moderator

    @seppim I have no idea since I did not test loading it with memdisk. I did not look but I suspect the iso image may be larger than 2GB (thinking memdisk is a 32 bit application and not a 64 bit app. But this is only a guess). I know when I was testing the boot.wim file on the iso was 1.3GB in size.
    I was able to get it to boot in uefi mode here: https://forums.fogproject.org/post/140212 but in bios mode it complains about needing bootmgr.exe in the iso image.

  • @george1421 Hello,

    thank you! This is now loading super fast. Just around 10sek.

    on my physical laptop he throw an error, there is not enough memory available to create virtual RAM disk.

    On my Virtual Box VM, I have first the same error (2.3GB Ram) and increase it to 4.2GB … then he booting the Hirens BootCD.

    But the Laptop has 8GB Ram … did you know why I get this error?

    My Parameters:

    initrd http://${fog-ip}/iso/HBCD_PE_x64.iso
    chain memdisk iso raw ||
    boot || goto start

    Thank you!

  • This post is deleted!
  • Moderator

    @seppim /var/www/html is the base path of the apache server. FWIW the fog program is installed in /var/www/html/fog directory. Its not required to save your iso to the fog directory. But since you are using just the ISO image that also implies you are using memdisk, which is a bios only program. UEFI systems will not be able to use this method of booting.

  • @tom-elliott Hello,

    how can I get the http path, where I need to copy the ISO to?

    I installed FOG on my Ubuntu 18 Server

  • Senior Developer

    @seppim To further clarify,

    TFTP is a limited protocol. What do I mean by this? Well it transfers data in blocks. As each blocksize is met, the TCP needs to resend validation of the next block. By default, tftp is set to check ever 512 bytes. So for every .5 KB it’s chunking, checking the prior, receiving the next, then downloading, and rinse repeat. At 1.3 GB this is going to take a very long time.

    Now there are methods to increase the block size. I believe the maximum block size, however, is 65536 Bytes. That means, essentially, every 64KB it will have to do the chunking process over and over. Still would take a long time with a 1.3GB file, though it might decrease the download time from 15 minutes to maybe 7.5 minutes (I’m just using numbers as a baseline, I have not tested this.)

    We use iPXE because the download sizes for TFTP to get the iPXE binaries is much much smaller. The UEFI driver ipxe.efi is 1,020 KB (basically 1MB). The Legacy driver undionly.kpxe 96.6KB (or about 97KB). I believe the UEFI stack takes so long to load because of this size difference. The efi driver is roughly 10 times larger than the legacy item. Even the legacy ipxe.pxe driver is only 352KB.

    So once the ipxe stuff is loaded, you are then having access to TCP protocols, not limited to TFTP items.

  • Senior Developer

    @seppim TFTP is a protocol that is limited to 10Mbps. That’s why. If you need more speed, you should chainload from TFTP to iPXE which will then use HTTP/TCP protocols to transfer the data, giving a much faster load time.