Slowness after upgrade to 1.5.7.102 (dev branch)

[rogalskij]

@Sebastian-Roth said in Slowness after upgrade to 1.5.7.102 (dev branch):

file /var/www/html/fog/service/ipxe/bzImage533

Good catch, found the typo and got it to deploy. The speed is the exact same however. I stepped through all the steps, verified the 5.5.3 Kernel and the speed is around 950mb per minute. Way slower than my usual. Part Clone is .3.12, I tried using the old init.xy file from 1.5.7 but it claimed I didn’t have enough memory. Very very odd. Do I just deal with it until stable version of 1.5.8 comes out maybe?

[Sebastian Roth]

@rogalskij said in Slowness after upgrade to 1.5.7.102 (dev branch):

The speed is the exact same however.

Too bad!

I tried using the old init.xy file from 1.5.7 but it claimed I didn’t have enough memory.

Can you try using init.xz and bzImage from https://fogproject.org/binaries1.5.7.zip as well as from https://fogproject.org/binaries1.5.3.zip - see if any of these will make speed things up again. Though you have to re-capture the image before you can deploy because those use an older version of partclone that is not able to deploy newer style images.

Do I just deal with it until stable version of 1.5.8 comes out maybe?

We can’t fix this without knowing what exactly is causing this. We don’t have your hardware here and so we need your help to test things and report back.

[Sebastian Roth]

@rogalskij In your initial post you said:

Dell Optiplex 9010 - 8gb ram, core i5, 500gb crucial SSD drive
Dell Optiplex 9020 - 12gb ram, core i5, 500gb crucial SSD drive
Dell Optiplex 7050 - 16gb ram, core i7, 500gb crucial SSD drive
Dell Optiplex 7060 - 16gb ram, core i7, not sure about the hard drive

Sounds pretty much like you have the same SSD in all those machines, right? Are those normal SATA SSDs or NVMe drives?

[rogalskij]

@Sebastian-Roth They are normal SSD sata drives for the most part. I was told by a member of the desktop team today though that they tried to image an Optiplex 7070 with an M2 solid state drive (the ram style drives) and it was around 1.4gb per minute.

I will certainly try to make some changes, but the fixes that came with the dev version far outweigh the speed issues I am having at the moment. Hoping some bug fixes in the 1.5.8 version will do the trick. I will keep testing as I can. Thank you all for your help for now!

[Tom Elliott]

@rogalskij while I understand the slowdown is problematic some of it seems bound to network speeds. For your tests are you only imaging a single machine, or multiples at the same time? Are they on a separated network or a congested one? No matter how fast an ssd disk you have, these things need to be thought of as well. What are the speeds of the performing network?

Please don’t take this as the only word. I just want to best understand the whole.

[rogalskij]

@Tom-Elliott It is possible it is something in my environment. Typically it is a single machine (imaged either via the console, or directly from the machine itself by a member of our desktop support team). It seemed related to the version because I first noticed it after I upgraded from 1.5.7 to the dev version of 1.5.8 and then later the dev version of 1.5.7.102. It went from like 12GB/min to 4GB/min or 1GB/min. The servers are production boxes so I can’t make too many changes without potentially affecting others but it still seems like it is related to the update I did. Perhaps the update of partclone? Also I noticed that when I pulled an image today for testing, the capture was super quick at 10GB/min but the deploys to the same machine and others like it were 4GB or less. I feel like I am missing something extremely mundane and obvious.

[Tom Elliott]

@rogalskij what’s the lowest version kernel you’ve tried?

[rogalskij]

@Tom-Elliott I tried some newer kernels like 5.3.3 as well as what shipped with 1.5.7 (kernel version 4.19.48). I tried using the original version of init.xz but it claimed my memory was too low or something of that nature so I switched it back. The speed didn’t seem to change at all on any of the different kernels, almost like the speed wasn’t related to those kernels. Also as another piece of information I am using UEFI pxe booting with ipxe.efi as the boot file.

I just updated to 1.5.7.115 but no change at all. Just for full disclosure.

[Sebastian Roth]

@rogalskij said in Slowness after upgrade to 1.5.7.102 (dev branch):

I tried using the original version of init.xz but it claimed my memory was too low or something of that nature

Can you try using init.xz and bzImage from https://fogproject.org/binaries1.5.7.zip as well as from https://fogproject.org/binaries1.5.3.zip - always use both init.xz/bzImage from the same ZIP archive to test. See if any of these will make speed things up again. Though you have to re-capture the image before you can deploy because those use an older version of partclone that is not able to deploy newer style images.

As well you might take a picture of the actual memory error on screen of you still get this. We might figure out what this is about.

[rogalskij]

@Sebastian-Roth Testing with newer init with partclone 0.3.13 and kernel 4.19.101 seems to fix my slowness in deployment of images. I am seeing speeds of 9GB or more in my testing now. I am guessing it is the partclone that is causing the slowness in some environments. Will continue to test and utilize 0.3.13 partclone to verify theory.

[Sebastian Roth]

@rogalskij Seems like I was actually wrong about you having a different issue than discussed in the other topic. Nevertheless I think it was good to have two topics to not mix up the information on who had tested what.

Thanks for your effort. I will update the official binaries tomorrow.

[rogalskij]

@Sebastian-Roth Thank you for all you and everyone does. I agree with you this was a good choice to make a second topic out of. This is working well now and I greatly appreciate all the assistance!