PXE & startnet.cmd Questions

[george1421]

From your post I can’t tell if you are having a networking issue (tcp/ip) or a SMB (network share) issue.

Your ping command might be improved a bit to test if its reachable.

ping -n 1 192.168.1.1 | find "TTL=" >nul
if errorlevel 1 (
    echo host not reachable
) else (
    echo host reachable
)

Other thoughts are the wpeinit starts the networking subsystem. You may need to create a small delay while the network comes up and the target gets an IP address.
So you could do something like:
timeout 10
or
ping 127.0.0.1 -n 11 > nul
To give the networking a chance to come up before trying to mount the network share.

While I have no basis for this, you have to consider a freshly booted computer may not be listed in DNS right away. Is your samba server doing any type of computer validation? Is samba showing any error in the error log when you try to connect?

[Zer0Cool]

@george1421 you know, you keep helping me you are gonna have to start charging me

Some of your ideas where thoughts of mine too, but have since realized some of them are not the culprit.

For example, wpeinit I would presume has the network up since the ping command works prior to net use. I will give timeout a try however as its basically the same concept I was trying with sleep.

I think the ping command is in that script mostly to add a delay and the verifying connection is kind of secondary. That was the only rationale I could come up with for pinging 4 times or as you pointed out I could simply ping 1 time and use it to verify the connection.

I am curious about your DNS statement though. Since I am using IP instead of hostname, shouldn’t that “circumvent” the DNS being an issue? If not maybe some sort of delay as you mention is needed, however I found ping -n 20 to not be long enough to make a difference. Also, doesnt explain why its not an issue BIOS booted.

My samba entry is super simple, just:

[global]
unix extensions = no

[pxeshare]
comment = PXE Server SMB Share
path = /pxeshare
valid users = @smbgrp
guest ok = no
browsable = yes
writable = yes
follow symlinks = yes
wide links = yes

I will take a look at the samba logs and see if any errors are present.

Thanks

[george1421]

@zer0cool I see that my smb.conf is a bit more complex, but I’m not seeing anything that jumps out at me as blatantly wrong with your setup: https://forums.fogproject.org/topic/10944/using-fog-to-pxe-boot-into-your-favorite-installer-images/2

The dns names should be OK, but remember we are dealing with SMB naming and not IP/DNS naming (not sure how to describe it) Its more on the wins side.

[Zer0Cool]

@george1421 Set logging to 10 and added a line to smb.conf to generate a log for each machine. Reviewing the log for the problem machine doesnt appear to reveal any clues.

I get some lines about it finding the user, then something like adding homes service for user... and lp_servicenumber: couldnt find homes.

When it booted and connected instantly and ran setup.exe within seconds it was the same thing as the last pass when net use worked within about 30 seconds and then setup.exe took ~5 mins to run.

It seems to me almost as if it runs fine after a period of time has passed but if I exit the setup and try too soon it has issues.

I am still at a loss with this, gonna try the timeout option peppered in, not sure what else to do beyond that.

Thanks

[Zer0Cool]

@george1421 Also, timeout 10 game the same “command not recognized error” as sleep.

Still, if it was a SMB issue wouldnt it be a problem when BIOS booting the machine and running winpe via pxe?

Its odd that BIOS booted it works instantly every time as expected but when UEFI booting it works right maybe 1/10 times.

I could live with an extra 1-2 minutes to run setup.exe, maybe, but waiting 5-10 minutes for it is a no go (especially if other are to use this).

Its also weird that when the share will mount but then the setup.exe takes forever to execute. In other words the command to run setup.exe is executed but it then takes a long time for the setup dialog to appear.

Is it possible winpe uses different NIC drivers under BIOS/UEFI?

The BCD, boot.sdi and boot.wim are the same for BIOS and UEFI correct? I dont need to pass iPXE a different set for BIOS vs UEFI do I?

I am kind of grasping at straws here

[george1421]

@zer0cool That was something I didn’t touch on before, what built in drivers are you installing in the winpe image? Did you use my instructions for creating the winpe image?

Also what hardware are you pxe booting that has this delay?

Using my winpe image I sent you, that will drop you to a command prompt. What happens if you execute the net use command by hand then?

[Zer0Cool]

@george1421 Ok scrap some of my prior comments…I went for a “sanity check” only to have it backfire on me.

It is now happening in BIOS boot as well, however seemingly not as slow (1-3 mins when the issue occurs vs 5-10 mins under UEFI).

The observation that seems the most sure is that time between runs appears to have an impact. If I run it and have not done so recently it works pretty much instantly. If however I run it, cancel and reboot and run it again I then have issues. Giving it some time between attempts appears to have the most noticeable impact of anything I have tried yet.

Does samba server (run from CentOS) have anything about it that may cause slow auth, prevent multiple connections from the same user, etc.?

Does the act of mounting the share in winpe in any way get stored server side? Like if I reboot and dont give it time to flush out it thinks its still connected or wont let it reconnect right away?

[Zer0Cool]

@george1421 I didnt feed it any drivers, was hoping for a machine agnostic winpe image…maybe wishful thinking. I can add the drivers to it.

Dell Precision 3620 is the box with the delay, ill try something else see if its an issue.

The image I am using starts up to a command prompt and runs the commands. When it fails to connect to the share I can manually type in the net use part and get it to connect.

setup.exe however appears to hang in the command window but given enough time eventually runs. I havent had an instance of it failing yet (as long as the share is mapped).

Gonna try another machine first, if it works on another machine differently I will try drivers in PE.

I am starting to lean towards a possible samba issue. I am considering even placing the Windows installation/winpe stuff on a windows server machine and serving them from there (I had this when I initially started this, then moved the install media to my FOG server). If it works from the Windows based share I will know its a samba issue on the FOG/CentOS server.

[george1421]

@zer0cool OK good choice on testing with windows server hosting the files. That was going to be my next suggestion.

I also would suggest using the dell winpe10 drivers (from my instructions) and loading those into your winpe image. There is nothing “dell” in there, they are common network and disk subsystem drivers. They do work on most hardware, even not dell hardware (an intel nic is an intel nic).

If you get super twisted up, it would be interesting to know what its doing during this pause. I’m thinking wireshark on a mirrored port to see if its trying to reach out to something on the network while it is waiting and then just gets tired and gives up.

[Zer0Cool]

@george1421 So I tried it on an R620, booted multiple times and connected to share and ran setup.exe almost instantly. Granted the machine takes ~4 mins to reboot and cycle back to the pxe menu.

I injected the drivers from the pack into the wim and just tried again on the Dell 3620, “same” problem in that it had issues. Actually (likely coincidentally) at the worse end of the spectrum of problems. Got error 53 trying to mount share, my loop took 12 cycles to finally connect, then setup.exe took roughly 1 min to show up.

So it looks like drivers may not have resolved things. I am beginning to think its these Dell 3620 workstations and their firmware thats just bad.

I am also wondering if its a networking issue as the data passes through a dumb swtich to where I am testing the 3620. Ill roll a R620 over to it and see if the R620 suddenly has issues then maybe its a network issue and not specific to the machine.

If all else fails ill try a share on a windows server to serve the install media.

Thanks

[Zer0Cool]

@george1421 Ok so not an issue with the network, R620 works just fine off the same switch.

I am gonna chalk it up to the Dell 3620’s firmware (which is the latest) being problematic. Its not the first time it proved to be, likely wont be the last.

I guess I can live with the issue as it always eventually runs setup.exe. As long as its not a wide spread issue and limited to that model machine I am gonna move on and just live with it.

Thanks for the help though, always good to have another person to bounce ideas off and to get other ideas from.