Fresh Install of Fog - Setup PXE Boot

[dpotesta50]

@george1421 Do I need to add anything to “setup a router address for the DHCP server”?

[george1421]

@dpotesta50 No since you have an isolated network

[dpotesta50]

@george1421 Install failed. Not connected to wireless so the repository couldn’t be setup.

[george1421]

@dpotesta50 OK so why can’t you connect to both wifi and ethernet? Is this a laptop where you have the bios (firmware) setup to disconnect wifi if the ethernet cable is connected?

[dpotesta50]

@george1421 Ethernet is literally just plugged into a switch that goes to nothing. My intent was to use that to connect a test device to for PXE boot. (This is all running on a Dell optiplex desktop) Anytime I “connect” to one, the other disconnects.

[dpotesta50]

This is really frustrating. Once I get wifi back up, FOG wants to bind to that NIC as it’s main. I don’t know the terminology it’s looking for when it asks if I want to change the default network adapter. If I say yes and enter the NIC’s name, it throws syntax error.

[dpotesta50]

Got it!
Kinda dumb, change to adapter number “2”.

[dpotesta50]

Got to the end of the installation where it updates the database schema. Site won’t open in Firefox. Just times out.
192.168.100.100/fog/management

[george1421]

@dpotesta50 Did you remember to disable the ubuntu firewall and set the selinux permissions to permissive as recommended in the prerequisites?

[george1421]

@dpotesta50 said in Fresh Install of Fog - Setup PXE Boot:

192.168.100.100/fog/management

This will only work if you are on the imaging network, to access the managment interface from the business side you will need to find the IP address of the wifi adapter.

[dpotesta50]

@george1421 I’m running on Ubuntu desktop, is this still required? (selinux permissions)

[george1421]

@dpotesta50 (sorry I’m a rhel guy) I’m not sure if ubuntu has selinux enabled or not by default. If its on, then its mandatory that you set it to permissive. If from the linux command prompt you key in cat /etc/selinux/config look for a line that says SELINUX=permissive or SELINUX=disabled If that is set then selinux will not cause you pain. If its set to enforcing then you need to change it as root and reboot.

[dpotesta50]

@george1421 It shows "SELinux status: Disabled

[george1421]

@dpotesta50 Ok so then selinux will not be in your way. Did you ensure that the firewall has been disabled? I know that IS on by default for ubuntu.

[dpotesta50]

@george1421 Yes I ran “sudo ufw disable”

[george1421]

@dpotesta50 So if you run ip addr show to get the IP address of the wireless interface and then from the business network attempt to connect to that ip addresss /fog ?

[dpotesta50]

@george1421 The dashboard is up and running. I can access it and all the options. I just tried to PXE boot a laptop to it, no server found.

[dpotesta50]

@dpotesta50 It’s very very slow though. Changing from option to option within the FOG program takes a minute or so.

[george1421]

@dpotesta50 Ok the slowness is from both networks?

OK, now lets work on one issue at a time.

So fog is the dhcp server, we need to make sure that isc-dhcp service is running on the fog server. Run this ps aux|grep dhcp and/or you can check to see if its listening netstat -an|grep 67

The fog installer should setup the isc-dhcp config file to look like this: https://wiki.fogproject.org/wiki/index.php?title=BIOS_and_UEFI_Co-Existence#Example_1

[dpotesta50]

@george1421