Boot menu configuration

[BedCruncher]

going to close this out now… helps when you specify

boot

as the last option.

[Quazz]

You should remove the :WHDD

It’s not necessary since the Menu item is already taking care of that and it might cause issues if you add any other items later on.

[BedCruncher]

I had simply modeled it after the entry that I put in above for DBAN.

[BedCruncher]

This post is deleted!

[BedCruncher]

Ran across another issue with a different piece of software that I was trying to add to the boot menu. It’s the HDT Tool project. What I currently have done is attempted to use an old config and files from a previous PXE server while modifying the relevant boot menu options.

I’ve also downloaded a bootable iso from the HDT site directly and mounted it in the same way as was done with the DBAN instructions. My current HDT boot configuration looks like.
with the url located at that address showing

Can anyone offer advice/help on this?

[BedCruncher]

Don’t know why it isn’t putting the images in the reply correctly. to clarify the above.

Boot Menu Entry

Menu Item: 
HDT

Description: 
Hardware Detection Tool

Parameters: 
kernel ${boot_url}/hdt/isolinux/hdt.c32
boot

URL Directory Listing

backgnd.png
boot.cat
chain.c32
display.png
hdt.c32
isolinux.bin
isolinux.cfg
memtest.bin
menu.c32
modules.ali
pci.ids
red.png

[Quazz]

@BedCruncher c32 is pxelinux files as far as I know.

You’ll probably need to chain it or something.

[BedCruncher]

@Quazz
Do you have a link showing how to do that with the new FOG 1.3 boot menus?

[Quazz]

@BedCruncher Try changing kernel to chain

Could be enough, not sure.

[BedCruncher]

@Quazz
Just changed. Will have to wait a bit before I can test that. I’m also upgrading that laptop to W10 to beat the deadline. Will post back once I can try again.

EDIT:
After modifying the menu entry as you wanted me to do, I simply get a black screen with blinking cursor.

[Tom Elliott]

@BedCruncher said in Boot menu configuration:

URL Directory Listing
backgnd.png
boot.cat
chain.c32
display.png
hdt.c32
isolinux.bin
isolinux.cfg
memtest.bin
menu.c32
modules.ali
pci.ids
red.png

What’s the variable for ${boot_url} set to?

[BedCruncher]

@Tom-Elliott
set fog-ip 192.168.240.10
set fog-webroot fog
set boot-url http://${fog-ip}/${fog-webroot}

[Quazz]

@BedCruncher Try chaining the menu file. Or maybe isolinux.bin

[BedCruncher]

@Quazz
Tried both, menu.c32 gives same blinking cursor. isolinux.bin provides the following.

[Quazz]

@BedCruncher Alright, so essentially, isolinux.bin is the correct one to use, but you need to edit isolinux.cfg so that it can boot over the network and doesn’t get stuck looking for the CD.

Unfortunately, I’m not entirely sure how to do that properly, if it’s even possible at all.

Also, I notice you shared hdt/isolinux folder contents, but what’s in hdt itself?

[BedCruncher]

@Quazz
the folder hdt is simply the mount point for the iso. It houses only the subfolder isolinux which contains the folder contents listed above. I will delve into the isolinux.cfg file to see where I can tweak it.Will report back with anything I can find.

[BedCruncher]

@Quazz
OK!!! Houston we have liftoff…

I was able to get this working by completely ignoring mounting the iso at all and instead doing what I had found in another forum with directly using memdisk and the raw iso. My working config for this is as follows