Multicast Issues on Centos 7

[BedCruncher]

@Wayne-Workman
No, I hadn’t. The command I ran was

firewall-cmd --permanent --zone=trusted --change-interface=em2

that was specified at this RHEL Firewalld page page. This seems to be this link firewalld.zones.

So I can change mine around and try it, but I wouldn’t have managed to do that particular one myself as I’m by no means a iptables guru. I will try to apply that tomorrow to test it out and let you know.

[Wayne Workman]

@BedCruncher If you find that the command I posted - or any command - allows you to multicast, I will immediately update all firewalld documentation we have in the wiki to reflect your success.

[dvchuyen]

@Wayne-Workman said in Multicast Issues on Centos 7:

Yes, I confirm the command work. I found it and solved my problem few days ago.

https://forums.fogproject.org/topic/7194/could-not-pxe-boot-input-output-error-when-do-multicast/31

[BedCruncher]

@Wayne-Workman
Sorry… I reread over what I had posted and it didn’t seem clear. The command above that I had ran was “supposed” to make it permanent, but failed to do so. I had to specify it statically in the NIC interface file. I will also double check the command you posted and test to see if it persists across reboots.

[Wayne Workman]

@dvchuyen I’ve updated the Fedora 23 and the CentOS 7 Wiki articles.

[BedCruncher]

@Wayne-Workman
I am not quite experiencing the same perfect results as @dvchuyen with regards to that firewall rule. I got it to work once, but since then it’s been extremely problematic.

 firewall-cmd --permanent --direct --add-rule ipv4 filter INPUT 0 -m udp -p udp -m pkttype --pkt-type multicast -j ACCEPT

verified it was in there with ipdtable-save and ran firewall-cmd --reload and systemctl restart firewalld. This was to ensure that it was all properly in there and correct. I even rebooted the server to ensure that there wasn’t something in the network service that was gumming it up. I have also deleted the tasks out of FOG and manually triggered it again and still hang.

[Wayne Workman]

@BedCruncher can you turn off your firewall and see if multicast works then?

systemctl stop firewalld

[BedCruncher]

@Wayne-Workman
I will do that really quick, but it seems like it might be a different issue with firewalld now. I got it to work again if I ran systemctl restart firewalld.service after a reboot. then it would start the imaging seemingly consistently. For some reason the rules aren’t correctly applying at boot time.

[Wayne Workman]

@BedCruncher From the behaviour you’ve been describing - I no longer believe this is a firewall issue.

Please just turn off firewall until we can complete troubleshooting with some sort of conclusive findings:

systemctl stop firewalld
systemctl disable firewalld

[BedCruncher]

@Wayne-Workman
God, I feel like I’m crying wolf all the time now. I disabled the firewalld service and it was hanging there as before. I then ran the commands

systemctl stop FOGMulticastManager
killall udp-sender
killall udp-sender
killall udp-sender
mysql -u root fog
TRUNCATE TABLE multicastSessionsAssoc;
TRUNCATE TABLE multicastSessions;
TRUNCATE TABLE tasks;
quit;
systemctl start FOGMulticastManager

I then tested it, and ran the multicast test. I again ran the commands to do all that above. I rebooted and ran the above commands again to ensure I was working clean and disabled the firewall and tested and so far it seems to be working. Please disregard.

[Wayne Workman]

@BedCruncher said in Multicast Issues on Centos 7:

@Wayne-Workman

Using one of the links, can’t remember which. I was able to get the server and client to send using the udp-sender and udp-receiver. So I know they can talk, but I had to use the command.

udp-sender --file /opt/fog/.fogsettings --log /opt/fog/log/multicast.log  --ttl 32 --nopointopoint --interface em2

if I dropped the last bit off then it would still try to grab em1 instead of em2.

An example now exists in two different places in the wiki. I want to merge the articles but it will be an involved process to do that - I’ll get it done.

For now, here are the two articles:

https://wiki.fogproject.org/wiki/index.php?title=Troubleshoot_Downloading_-_Multicast
2.
https://wiki.fogproject.org/wiki/index.php?title=Multicast