Display errors on queued computers (Unicast)

[Wayne Workman]

@Tom-Elliott

A colon would look nicer.
0:5:35 left…

0:2:29 left…

[Tom Elliott]

@Wayne-Workman that’s not a timing to show you how long you have until you get to image
that’s a timing to show how long it’s been waiting.

[tian]

@Tom-Elliott said:

@tian Did all 6 show the same message in the first 5 minutes of it “waiting”?

I just watched the queued computers for 10+ minutes. All of the queued computers show “There are 0 before me” from the very beginning. The number never changes to 1, 2, 3 or sth. else.

Also thanks for the explanation for the time format.

[Wayne Workman]

@Tom-Elliott Well, still, it’d look nicer.

In line for 0:8:23

[Tom Elliott]

All should now be setup properly.

Please update and if you can test with multiples and let me know.

[tian]

@Tom-Elliott I just did a test with version 6971 and it looks different now but still seems not completely correct.
The number in “There are x before me” is counting now, but it displays the same number on all the queued computers again:

• When there are four comupter waiting it is “3” on all waiting computers
• with five computers it is “4” on all waiting computers
• at the end all six queued computers display “There are 5 before me” on all waiting computers
  I waited 10+ minutes again, but the computers didn’t display different numbers.

Here you can see the change of the number (that takes place on all computers) when one more computer is waiting:

[Tom Elliott]

@tian Can you update and try again? I re-adjusted how the counting is to work, in hopes it will work a little better.

[Cpasjuste]

Hi,

Just a little message to say that i do have the same problem with SVN 6975 : i have an “attempting to check in” loop when trying to restore an image. It was working fine before i updated (i don’t remember which version i was previously but it was SVN 69xx).

[Tom Elliott]

@Cpasjuste What do you mean? Pictures please if possible.

[Cpasjuste]

@Tom-Elliott sure, here it is ! So i create a basic task (deploy), then it just loop on the “attempting to check in”. This task did work fine (same machine/image) a few hours ago just before i update to latest git (svn).

[Cpasjuste]

Just a little more information i just found : if i click the “force task to start” button in the “Task Management”, then the deploy task does start. By the way, if you need some testing just send me a mail. I do have a good linux and developement knowledge which may help to debug if needed.

[Tom Elliott]

@Cpasjuste Should be fixed, sorry about that.

[Cpasjuste]

@Tom-Elliott

Thanks and no problem, we know what we sign for when we use the devel branch I’ll update in a few minutes and let you know.
Edit: i confirm that it’s fixed.

[tian]

@Tom-Elliott Thanks for your hard work. Now the numbers are changing and are different. But these are totally mixed up now (Version 6977):


The pictures were taken from different computers.
A lot of times there still are the same numbers to displayed on different computers at the same time (maybe the 5 seconds interval is too huge to see if there are moments with double numbers).

Is there anything else I can provide?

(In fog 0.32 the queued numbers were/are fine - with the difference that there was/is a delay till free slots can be used by queued computers. Now in the recent versions the computers starting up first gets the free slots - but that is ok.)

[Tom Elliott]

@tian While I’m glad we’re closer, I hope to have finally gotten this more properly solved. The checkin process was constantly updating the time which is why you would see the numbers change (depending on the other host checking in).

It should be good now, Hopefully.

[tian]

@Tom-Elliott said:

@tian While I’m glad we’re closer, I hope to have finally gotten this more properly solved. The checkin process was constantly updating the time which is why you would see the numbers change (depending on the other host checking in).

It should be good now, Hopefully.

I don’t want to tell you - but now (Version 6981) all queued computers display “There are 0 before me” again …(It also would be fine just to display the total number of computers waiting - or just display the time waited - if this problem consumes too much time at the moment…)

[Tom Elliott]

@tian I’m fairly sure it should work properly. I only say this because I have the time setup now and I tested with a 1 client node and 3 tasked hosts.

I don’t know the exact reasoning that these things occur, but I don’t think they’re hindering anything. Maybe group tasks will suck for this?

[tian]

@Tom-Elliott Maybe the group deployment task is not working correctly with this in the trunk versions. Except the wrong display the other things are working. We also just use one server (and on this one the default storage/node). We mostly use group deployment tasks - single deployment tasks are not used that often and wouldn’t reach the limit we set.

Thanks for all the effort you put into solving this.

[Tom Elliott]

@tian My worry for the display is that all the clients have the same time starting out. Because of this, they all get updated at the same time too. I update the check in times if they have timed out now, so order should be maintained. However, if all times are identical, there’s no real way to know which one is first or not. Again, it’s a minimal problem, though I can understand the “huh?” issue.

[Wayne Workman]

@Tom-Elliott But the count issue is solved? The “There are 5 before me” message is accurate?