rEFInd - Initializing after disable Secure boot

[george1421]

@poizzon This menu we can work with. If you wait for a period of time does the system boot?

[poizzon]

i don’t wait.
just pressing enter and booting to windows normaly.

[george1421]

@poizzon

Here is a repeat of a post helpfully provided by @Enrico

Those settings fit more situations, I think (but I can’t assure that) but you can tune them.

scanfor selects where it is going to search for boot loaders. In my case, “internal” does not find bootcamp boot loader, so I add “hdbios”.

scandelay 5 is needed because the default 0 is too quick to permit the bootcamp become available.

timeout 5 is needed because the default -1 goes straightforward to boot the default loader and does not show the two os options. So, this one is needed if you have a multiboot system only.

In your case, check scandelay and set it for 5, and then timeout to -1 to pick the default boot loader without delay. Yes I understand the post was about OSX (Apple), but UEFI is UEFI.

[poizzon]

@george1421 I think this menu is not a problem, as I understand it is due to scanfor …

by default are set like you say

....
timeout -1
....
scan_delay 5
....

[george1421]

@poizzon I think here we have 2 issues.

1. The system is setting at the refind menu, where you pick enter and it boots into windows.
2. The system doesn’t discover any efi boot partitions on the computer so it posts your earlier message.

In regards to the computer that doesn’t find any efi boot partitions, what hardware is this Manufacturer and model?

[poizzon]

@george1421 All computers are Dell’s :
Latitude E5570
PowerEdge T20

As I remember installation of this computers was made with secure boot enabled.
Maybe I had to install with the option turned off secured boot ?

Partitions are GPT

[george1421]

@poizzon The Secure boot question is only an issue related to pxe booting non-microsoft operating systems. With secure boot on, only operating systems with a valid certificate can boot on that hardware. So secure boot only impacts booting linux and iPXE on the target computer and not the quality of the image on the target computer.

Can you take one of these non-refind-booting systems and boot it into windows and then do a print screen of the disk manager table partition layout and post the picture here? I would be interesting in seeing what the disk geometry looks like,

[poizzon]

@george1421 it is genuine Dell partition schema

DISKPART> list disk

  Disk ###  Status         Size     Free     Dyn  Gpt
  --------  -------------  -------  -------  ---  ---
  Disk 0    Online          465 GB      0 B        *

DISKPART> select disk 0

Disk 0 is now the selected disk.

DISKPART> list partition

  Partition ###  Type              Size     Offset
  -------------  ----------------  -------  -------
  Partition 1    System             499 MB  1024 KB
  Partition 2    Reserved           128 MB   500 MB
  Partition 3    Primary            455 GB   628 MB
  Partition 4    Recovery           939 MB   455 GB
  Partition 5    Recovery             8 GB   456 GB

DISKPART> list volume

  Volume ###  Ltr  Label        Fs     Type        Size     Status     Info
  ----------  ---  -----------  -----  ----------  -------  ---------  --------
  Volume 0     C   OS           NTFS   Partition    455 GB  Healthy    Boot
  Volume 1         ESP          FAT32  Partition    499 MB  Healthy    System
  Volume 2                      NTFS   Partition    939 MB  Healthy    Hidden
  Volume 3         Image        NTFS   Partition      8 GB  Healthy    Hidden

DISKPART> detail disk

WDC WD5000LPLX-75ZNTT0
Disk ID: {CF2E2F9A-2807-46A7-889D-FA8A5A099BB1}
Type   : RAID
Status : Online
Path   : 0
Target : 0
LUN ID : 0
Location Path : PCIROOT(0)#PCI(1700)#RAID(P00T00L00)
Current Read-only State : No
Read-only  : No
Boot Disk  : Yes
Pagefile Disk  : Yes
Hibernation File Disk  : No
Crashdump Disk  : Yes
Clustered Disk  : No

  Volume ###  Ltr  Label        Fs     Type        Size     Status     Info
  ----------  ---  -----------  -----  ----------  -------  ---------  --------
  Volume 0     C   OS           NTFS   Partition    455 GB  Healthy    Boot
  Volume 1         ESP          FAT32  Partition    499 MB  Healthy    System
  Volume 2                      NTFS   Partition    939 MB  Healthy    Hidden
  Volume 3         Image        NTFS   Partition      8 GB  Healthy    Hidden

[poizzon]

@poizzon said in rEFInd - Initializing after disable Secure boot:

Partition 1 System 499 MB 1024 KB

Today I made a test with VMware Workstation with a blank disc and turned UEFI function.
I got the same error.

p.s.: after instaling WIndows, and tryng boot from network - same situation

[WillingMost7]

@poizzon Same here. I tried replacing in S: partition to the latest rEFInd but still getting stuck at “initializing”.