Identical NVMe drives

[Sebastian Roth]

@mrp I just added another fix to the init. Make sure you re-download the file from the link below (updated the file) before you start testing.

[mrp]

@sebastian-roth Yesterday I downloaded the init file (init_adv_primary_disk.xz) and replaced the /var/www/html/fog/service/ipxe/init.xz file with the downloaded one.

I did multiple single and multi-disk deployments (multiple partition not resizable) as well as multiple single and multi-disk captures (multiple partition not resizable). I specified the order of disks using the Host Primary Disk field (wwn(nvme),wwn(nvme),device-name(sata) ; serial(nvme),serial(nvme),device-name(sata) ; also single disk capture and deploy by specifying a single disk like serial(nvme) or wwn(nvme)).

With the new init file, the NVME drives still got picked up seemingly randomly in all tested scenarios.

When working on single NVME drives (specified with serial or WWN), the partclone progress screen always showed /dev/nvme0n1 being captured/deployed, regardless of the NVME drive being specified in FOG and the drive that was picked by FOG.

I tested both with the normal setup (2xNVME, 1xSATA) and without the SATA drive. Interestingly, when testing with (2xNVME, 1xSATA) and specifying the Host Primary Disk like WWN1,WWN2,sata_device_name (or the same with serial), the capture/deployment always started with the SATA drive and then continued with the two NVME drives.

Maybe the serial and WWN entries were found to be invalid and/or simply skipped by FOG? The WWNs and serials were correct, I double checked each of them.

[Sebastian Roth]

@mrp Thanks heaps for testing and letting me know!

Can you post the actual information you set as Host Primary Disk in the FOG web UI for the specific hosts? Just a few examples.

[mrp]

@sebastian-roth I sent you the examples with WWNs and serials in chat.

[Sebastian Roth]

@mrp said:

Yesterday I downloaded the init file (init_adv_primary_disk.xz) and replaced the /var/www/html/fog/service/ipxe/init.xz file with the downloaded one.

Now that I think about it again I am wondering if you checked the Init Version number shown on boot up? Just to make sure it’s the correct file used.

[mrp]

@sebastian-roth With the replaced init file it showed Init Version 20211009 during captures/deployments. Sadly, I did not think of checking whether the init version has changed. We have FOG 1.5.9, what is the default init version of that release?

[Sebastian Roth]

@mrp said in Identical NVMe drives:

With the replaced init file it showed Init Version 20211009 during captures/deployments.

Perfectly fine! It’s the latest as of now.

We have FOG 1.5.9, what is the default init version of that release?

Not shure exactly, but more like 20200906 - definitely a huge difference to the 20211009 you have now.

I will look into this over the weekend!

[Sebastian Roth]

@mrp Found some time to look into this again. The issue I have with testing this is that neither serial nor WWN can be looked up by lsblk in my virtualbox setup. I have no idea why this is the case. Tools lilke udevadm, hdparm and so an show serial and WWN but lsblk does not. So in my tests I am using the disk size (blockdev --getsize64 /dev/sda) as parameter and it works.

I added some debug statements to the scripts to further debug this. Please download the updated init, place it on your FOG server, schedule a debug deploy task and boot the host up. After the PXE boot you should see this message: “Trying to sort enumerated disks according to Host Primary Disk setting” - New init version is 20211025.

Please take a picture of the screen where you see this message and post that here in the forums.

[mrp]

@sebastian-roth Sorry for the delay, today I had some time to test this.

Please download the updated init, place it on your FOG server, schedule a debug deploy task and boot the host up.

I tested the new init with debug tasks with the following host primary field values:

serial(nvme1),serial(nvme2),device-name(sata) = eui.0025385601500953,eui.0025385601500954,/dev/sda

wwn(nvme1),wwn(nvme2),device-name(sata) = S4EVNG0N600905D,S4EVNG0N600906P,/dev/sda

wwn(nvme1),serial(nvme2),device-name(sata) = S4EVNG0N600905D,eui.0025385601500954,/dev/sda

Just for double checking, I also checked lsblk -pdno NAME,SERIAL,WWN again:

[Sebastian Roth]

@mrp Thanks for the pictures, great documentation of the test and your patience!!

Find another updated init binary on github that might possibly solve the issue but if not it will definitely give us further insight on why it doesn’t work with serial and WWN yet.

[mrp]

@sebastian-roth I tested the same debug tasks with the new init. It seems that the WWN cannot be retrieved by the init, but with the serial it seems to work now.

Find another updated init binary on github that might possibly solve the issue

serial(nvme1),serial(nvme2),device-name(sata) = eui.0025385601500953,eui.0025385601500954,/dev/sda

wwn(nvme1),wwn(nvme2),device-name(sata) = S4EVNG0N600905D,S4EVNG0N600906P,/dev/sda

wwn(nvme1),serial(nvme2),device-name(sata) = S4EVNG0N600905D,eui.0025385601500954,/dev/sda

[Sebastian Roth]

@mrp Thanks again for testing. Looks better now but still not perfect. I wonder why it doesn’t find the WWN at all. Can you please run the following commands in a debug command prompt and post output here:

lsblk -pdno WWN /dev/sda
lsblk -pdno WWN /dev/nvme0n1
lsblk -pdno WWN /dev/nvme1n1

[mrp]

@sebastian-roth No problem, here it is:

[Sebastian Roth]

@mrp Ah well I see. Our FOS lsblk command is not able to retrieve the WWN information. Too bad. Not sure if there is anything we can do about it. Good you can use the serial numbers for now.

Would be interesting to see if this is not working in general or only might be an issue on your computers.

[Sebastian Roth]

@testers @moderators Can some people please test running lsblk -pdo NAME,SERIAL,WWN in a debug session (doesn’t matter if it’s capture or deploy). No need to take a picture and post that here. Just let me know of WWN is shown in the output.

[george1421]

@sebastian-roth On any computer with an NVMe drive or only one that has more than one nvme drive??

[mrp]

@sebastian-roth Sorry for the delay, I have some busy days behind me. I ran the debug task and lsblk on an Intel NUC with a single NVME drive. On the NUC, the results were the same, the WWN field was empty, while the name and serial were ok.

[Sebastian Roth]

@george1421 said in Identical NVMe drives:

On any computer with an NVMe drive or only one that has more than one nvme drive??

Really on any machine you have available, be IT single or multi disk, HDD or NVMe…

My guess is that our FOS lsblk has this kind of bug where it cannot read the WWN.

[Sebastian Roth]

@testers Anyone keen to test and give some feedback on the output of lsblk -pdo NAME,SERIAL,WWN in a debug session? No need to take a picture and post that here. Just let me know of WWN is shown in the output or empty.

[george1421]

@sebastian-roth said in Identical NVMe drives:

Anyone keen to test and give some feedback

Sorry I forgot about this thread. I’ll give you the results tomorrow. You just need a yes or no on the WWN or do you want me to test with multiple hardware to see if its hardware specific?

I think lsblk is part of busybox. I don’t know if buildroot has the full app or not. I haven’t look as of now.