Cannot find disk on system (getHardDisk) - Cannot reimage new hardware

[michaeloberg]

@george1421 said in Cannot find disk on system (getHardDisk) - Cannot reimage new hardware:

Also update your fos linux kernels. Be aware this has nothing to do with the FOG Host server but with FOS Linux. Goto FOG Configuration -> Kernel to update FOS Linux kernel.

Thank you kindly for the information regarding the HDD configuration in the system BIOS. After I changed the RAID setting to AHCI and reloaded Windows I was able to register the host - well sort of

I stepped through the process of “Perform Full Host Registration and Inventory” and can now find the host in my FOG Dashboard, but when I create a capture task for the image and reboot, F12, select IPV4 PXE, it comes back to the White screen and in RED states : Host is NOT registered! I don’t know if this makes a difference but I am using a Dell Thunderbolt dock with integrated NIC, the computer doesn’t have an RJ45 jack.

In addition to this, when I go to FOG Configuration-> Kernel Update
The right windows says “This section allows you to update the Linux kernel which is used to boot the client computers. In FOG, this kernel holds all the drivers for the client computer, so if you are unable to boot a client you may wish to update to a newer kernel which may have more drivers built in. This installation process may take a few minutes, as FOG will attempt to go out to the internet to get the requested Kernel, so if it seems like the process is hanging please be patient.”

I don’t see an option to update (button or instructions to fire off the process).

Attached is the screen capture of client screen where it states it is not registered, also a screen capture of the client in FOG, and finally a screen capture of the Kernel Update settings.

[george1421]

@michaeloberg I guess a couple of things here.

The host not registered kind of indicates the mac address of the target computer has changed since registration. If you are using a wd19 dock that should have a static mac address assuming you are using the same computer you registered with. (fwiw, the wd15 dock is much more stable than the wd19 dock but I don’t think the wd15 is thunderbolt, only usb-c) My daily driver is a 7400. If you look in the bios (firmware) on the system information page there is a passthrough mac address. This address needs to (should) match the host registration in FOG.

For the 7400 we needed to go into System Configuration->Thunderbolt Adapter config.
Enable thunderbolt
Enable thunderbolt boot support
enable thunderbolt pre-boot modules
No security

To make it pxe boot reliably (and use a wd15 dock or the usb-c to ethernet dell dongle.).

Kernel update, does your FOG server have internet access? If you access the internet via a proxy server you need to configure that in FOG so it can reach the FOG servers online to read in the kernels. On the screen you shown there should be large buttons under the header to allow you to down. If your fog server can’t reach the internet because of your security policy there is a method to manually download the updated kernel.

[michaeloberg]

@george1421 A bit puzzling this one is. I deleted the Host from FOG, then re-registered it using a different name: ST-3501. Then I created an image upload task for the Host, and rebooted - same thing “Host is not registered!”. So I rebooted and when I hit F12, Choose USB NIC (IPV4), then it states - "Start PXE over IPV4 on MAC: CC-48-3A-A9-6D-16. See attached:

But when I choose Client System Information from the FOG Boot menu it gives me a different MAC which matches the printed label on the WD19 Dock:

When I click on the Host name in the dashboard, the MAC it lists there is the MAC on both screens in the previous Pic.:

So I am not sure where that, I will call it “Booting MAC address of " CC-48-3A-A9-6D-16” is coming from and that might just be my problem?

Also regarding updating the Kernel, I don’t have an option to download anything. I don’t have proxy configured and not sure what to try next.

[michaeloberg]

@michaeloberg @george1421 My colleague figured out that we need to disable the MAC address pass through and now it is uploading I need to wait for this to finish then pull it down to have a valid test, but things are looking up for imaging at least. Still no progress on the Kernel update, is that needed?

[george1421]

@michaeloberg Kernel update. If your fog server doesn’t have direct internet access then you can download the kernels from here: https://fogproject.org/kernels/

Grab these two files
https://fogproject.org/kernels/Kernel.TomElliott.5.6.18.64
and
https://fogproject.org/kernels/Kernel.TomElliott.5.6.18.32

Rename them to this respectivly.
Kernel.TomElliott.5.6.18.64 -> bzImage
Kernel.TomElliott.5.6.18.32 ->bzImage32

Watch your case because it IS important.

Now move those files to /var/www/html/fog/service/ipxe directory. It probably wouldn’t hurt to rename the existing ones in case you need to go back for some reason.

The next time you pxe boot the updated kernels will be used.

[michaeloberg]

@george1421 I am such a novice at this I don’t know how/where to start. I downloaded the 2 files to my Windows 10 PC, and renamed them (watching the case) to my downloads folder. Then I putty into my FOG server, but am stuck. I am guessing I was supposed to download the files from my FOG server but don’t know how. Simple tasks like that - downloading files, moving, and renaming are difficult because I have no Linux knowledge. In the DOS world I can easily copy, rename, move, create, delete folders but the syntax is different and just a simple, type this “xyz” to download files, then type “abc” to navigate to your Kernel folder, then “qwe” to rename your old files, then whatever else would be helpful. I am sorry as this has to drive you mad working with people like me. I need to learn, I want to, but for lack of better excuses - I don’t have time.

Thanks,

Mike

[Sebastian Roth]

@michaeloberg Give that a try (run as root) :

cd /var/www/html/fog/service/ipxe
mkdir backup_kernels
mv bzImage* backup_kernels
wget -O bzImage https://fogproject.org/kernels/Kernel.TomElliott.5.6.18.64
wget -O bzImage32 https://fogproject.org/kernels/Kernel.TomElliott.5.6.18.32
chown www-data:www-data bzImage*

[michaeloberg]

@Sebastian-Roth I was able to follow along until the line where I type the wget command, it comes back with “failed:Temporary failure in name resolution” Below is everything I had type in Putty:

root@fog-server:~# cd /var/www/html/fog/service/ipxe
root@fog-server:/var/www/html/fog/service/ipxe# mkdir backup_kernels
root@fog-server:/var/www/html/fog/service/ipxe# mv bzImage* backup_kernels
root@fog-server:/var/www/html/fog/service/ipxe# wget -O bzImage https://fogproject.org/kernels/Kernel.TomElliott.5.6.18.64
–2020-10-13 12:35:45-- https://fogproject.org/kernels/Kernel.TomElliott.5.6.18.64
Resolving fogproject.org (fogproject.org)… failed: Temporary failure in name resolution.
wget: unable to resolve host address ‘fogproject.org’

[Sebastian Roth]

@michaeloberg So you don’t have internet access from this server?

[michaeloberg]

@Sebastian-Roth Unknown, I should. I know in the past when I ran updates I had to download updates by typing in:
sudo apt-get update && apt-get install git

then something like

git checkout dev-branch

and it would download something from

https://github.com/FOGProject/fogproject.git/root/fogproject

This is from my notes when I updated the fog server in Feb. 2019. So these may not be entirely accurate but I know that it downloaded something??

I can also ping 8.8.8.8 from the FOG server. Lost I am

[Sebastian Roth]

@michaeloberg Let’s switch to chat -> speech bubble in the top right corner of the forum.

[Sebastian Roth]

Turns out the DNS server was not ser correctly and the server got it’s IP via DHCP. We got that fixed.