I recently installed fresh fog 1.2.0, then migrated the images and hosts over, Ive been reading that the images would not be known as partimage and you need to enable the gui option to make the necessary changes.
Where do i Find the gui option to enable it?
So where is the option to enable the selection between partimage and part clone? is it under fog settings?
So i decided to go back a recheck everything including my bosses changes to the DHCP. It appears that it was only changed under server options and not scope options. So yea i’m ready to do the same to my keyboard… After making sure that it was changed on both i was able to successfully pxe boot and i am currently uploading my image to the server… Thank you all so much!! couldn’t have done it with out everyone.
One final question it gives me the choice for part clone or part image, i selected part image but in noticed that during the imaging part clone is running , and its moving along quite slowly.
Either way progress none the less.
what is your value for [FONT=Ubuntu][COLOR=#555555]FOG_TFTP_PXE_CONFIG_DIR under fog settings tftp server?[/COLOR][/FONT]
What is different between the .032 and 0.33 it seems that the tftp only works when going to pxelinx.0
i checked the folder [SIZE=4][FONT=Times New Roman][COLOR=#000000][FONT=courier]/etc/xinetd.d/tftp[/FONT] and there isn’t a tftp file only chargen, daytime, discard echo and time[/COLOR][/FONT][/SIZE]
i ran the tftp and it gave me the following…
timeout occurred
connect request failed
Fog installed through script using the wget method from mastacontrola
My fog is on my ubuntu 12.04 why am I installing the tftp client on Windows?
I have the file in the ipxe folder
yes same information just a fresh 0.33b install instead of 0.32
The only thing different is that i took you advice and did a clean install, with a larger drive
That part is already done, i did that with the original fog box per your instructions and have not changed anything on the DHCP server.
my 67 on my DHCP is = undionly.kpxe
Sorry i misunderstood
My DHCP server is seperate than my fog…
i have already made the changes to option 66 and 67 on my DHCP
as far as my fog machine goes its the same pc with a new drive and new install.
i am able to get into the fog web portal 192.168.5.5/fog
when i try to pxe from client i get
"TFTP.
PXE-T01: File not found
PXE-E3B: TFTP Error - File not found
"
i have done a sudo stop tftpd-hpa
sudo start tftpd-hpa which is what usually was the problem during 0.32
do i need to create the dnsmasq as stated in [url]http://www.fogproject.org/wiki/index.php/Using_FOG_with_an_unmodifiable_DHCP_server/_Using_FOG_with_no_DHCP_server[/url]
I dont believe i should because the dhcp would handle all of that right?
Ok so stepping back a little bit what do i need to do to fix the tftp problem… new install mysql is working because i can long into fog. what is the missing peice?
ok so i dont have a dnsmasq folder and ltsp.conf
Ok looking at the fog setup my DCHP router address is empty and my dhcp dns address is as well byt my server ip address is set
Yes i originally had a machine with fog 0.32 on it and updated but it left me with some issues. So i got new drive and reinstalled 12.04 and fog 0.33b fresh. would that DHCP setup be during the fog install? reading through the documentation should i be looking to modify an ltsp.conf file?
there insnt a /tftpboot/pxelinux.cfg/ file anymore…? should there be one in my tftpboot folder?
TFTP.
PXE-T01: File not found
PXE-E3B: TFTP Error - File not found