@Tom-Elliott Thanks Tom, have updated and performed an upload using Single Disk Resizable and it uploaded without any errors.
I also then performed a deployment task of the Image and it was successful, windows boots up fine etc… just saw it come up with an error about changing the hostname.
@Tom-Elliott Hi Tom, running that command seems to have resolved the issue and it was able to successfully upload the image to the FOG server. This is while the image was set to Multiple Partition Image - Single Disk (Not Resizable)
When I changed it to single disk - resizable, the below error appeared…
@Tom-Elliott ok cool… will do that now.
The output of the previous command was…
Invalid partition data!
@Tom-Elliott Hi Tom, I updated to trunk 6084 and did the debug testing as you requested. Screen shots below…
Image set to Single Disk - Resizable
Image set to Multiple Partition Image - Single Disk (Not Resizable)
@Tom-Elliott Thanks Tom. I’m currently interstate for this week so once I’m back at our main office next week, I will perform the testing.
Thanks
@Arrowhead-IT Yup - updated to 5964 this morning on the test server.
@Sebastian-Roth Here’s the results of the Debug…
Here is the upload attempt when the Image is set to Multiple Partition Image - Single Disk (Not Resizable)
Damn that screen on the XPS 13 is shiny 
@Tom-Elliott I did leave it running for 5 mins but it still had not progressed on either one except Raw.
Hi Tom,
Got the Dell tech to replace the motherboard today.
Latest Fog trunk now recognises the nvme SSD.
When the Image is set to Single Disk - Resizable, it hangs at…
* Saving original patition table......................
When Image is set to Multiple Partition Image - Single Disk (Not Resizable), it hangs at…
* Now FOG will attempt to upload the image using Partclone
* Processing Hard Disk: /dev/nvme0n1
When Image is set to Raw Image, it starts the upload…
I’m fine with using Raw Image if that’s what works. 
Hi Tom,
Location selection issue has been resolved in trunk 5929 so you may set this as resolved.
Thanks again!
@Tom-Elliott Thanks! Will test this morning and report back.
@Tom-Elliott Ok no dramas. Will test as soon as the notebook is repaired by Dell. Cheers
@Tom-Elliott No worries. I just noticed it on the test server that I updated and was testing on.
Hi all,
Apparently there’s a delay with the replacement motherboard for the new XPS 13.
So you guys can most likely close this case for now as I noticed that @Arrowhead-IT has confirmed that it’s resolved in the latest trunk.
Cheers
Further to this, if say I have 2 locations displaying…
ID# 2 - Melbourne
ID# 1 - Sydney
Pressing ‘1’ just keeps prompting for the location ID.
If I enter ‘11’, that then progresses.
Same if I were to press just ‘2’, it won’t work, but pressing ‘22’ will progress.
Hi guys,
In the latest trunk, there appears to be a bug with Location selection.
When it come to selecting a location, if I enter the number for the location I want, it doesn’t seem to accept it. It just flashes back like as if I entered a number that is incorrect and won’t let me proceed any further.
Running on CentOS 6.7
Trunk 5927
Cheers
Hi guys,
I did update the inits with the ones below and I noticed an odd behaviour where I was imaging a standard notebook with a standard SSD. After it had completed the partclone process, and it went through resizing the partition etc… rather than restarting the PC to boot up normally, it immediately restarted the partclone download process all over again.
After reverting back to the original inits, this didn’t happen.
Just thought I’d let you know.
@Arrowhead-IT Thanks for letting me know.
Dell haven’t yet fixed up the notebook as yet. Still waiting on parts.
Have updated to those inits. Will test as soon as the notebook is fixed and report back.
@Sebastian-Roth No I haven’t as yet sorry. I went to try that today but the notebook will no longer boot up lol. Won’t even POST.
So have contacted DELL to organise a replacement. Will let you know how it goes after that.