Hi all,
I would like to thank you all for your help. I installed the latest trunk and i am able to inventory and install the image on it. Hopefully i will not be getting to many bugs from now on.

Hi guys, i just noticed that my reply from friday is not there. I did the installation of the last version of Fog. I still had the same problem. I then tried to install another image and this time it worked. (It did not work previously after the update!) So i used my backup copy of my images and everything is ok now. Thank you for your help again!

Good morning everyone! I appoligise for not replying any sooner. I did some testing and this i was able to solve my problem. I realized that i was able to PXE boot from a physical machine. Just not with a virtual machine with Windows 7 X64 in Hyper-V. I found a post that explain to use a legacy network card. I did the change and i was able to register my VM in FOG. Thank you all for your help. Incase, here is the link i found…
https://www.petri.com/boot-hyper-v-virtual-machine-using-pxe

Good day Yall!

Hi all,
I wanna thank everyone for their support. I was able to free up my storage node in the dashboard by login in my Ubuntu Server via Putty and erasing the images that were supposed to be erased in /images.

Have a great day!

I think i just found what i did wrong. If i delete from image management. The dashboard does not update. If i go in image management, choose an image then delete, i have an option to delete storage. Butfor now is there a way make my dashboard accurate? Thank you.

Ok thank you. if the image is erase from the gui. Is there another way to delete it? Thank you

Thank you. How do i delete the image definition in webif?

Hi,
I’m sure this is an easy answer. My storage node is almost full. I erase the images that are no longer required. But on the dashboard, it show still as full. Irebooted the server in case. Thank you in advanced.

Good morning everyone! I appoligise for not replying any sooner. I did some testing and this i was able to solve my problem. I realized that i was able to PXE boot from a physical machine. Just not with a virtual machine with Windows 7 X64 in Hyper-V. I found a post that explain to use a legacy network card. I did the change and i was able to register my VM in FOG. Thank you all for your help. Incase, here is the link i found…
https://www.petri.com/boot-hyper-v-virtual-machine-using-pxe

Good day Yall!

@george1421 Ok thank you for you reply. I change option 67 to snponly.efi?
At this time, i am trying to buid a template on a VM (Windows 7 X64) in Hyper-V. My DHCP server is in fact Server 2012.

Option 67 in DHCP = undionly.kpxe
Option 66 in DHCP = IP adress of FOG server
The intended target OS is Windows 7. If i disable secure boot, the PXE is not detected.

Good morning everyone. I have to setup Fog in an Hyper-V environment. I installed Ubuntu Server 14.04-4 LTS and Fog 7009. The web interface is working fine. I am able to boot PXE but i am getting these message…

• Station IP adress is x.x.x.x
• Server IP is x.x.x.x
• NBP filename is undionly.kpxe
• NBP filesize is 92249 Bytes
• Succesfully downloaded NBP file.
• Boot Failed. EFI network. Failed Secure boot Verification
• Boot failed. EFI SCSI Device.
• No Operating System was loaded…
  In the past, I installed Fog server on a Physical machine, On VirtualBox and ESXi without any problem. Any help on my problem? Is is compatible? I saw many post about performance issue with Hyper-V. So i assume it is compatible? Thanks!

Hi guys, i just noticed that my reply from friday is not there. I did the installation of the last version of Fog. I still had the same problem. I then tried to install another image and this time it worked. (It did not work previously after the update!) So i used my backup copy of my images and everything is ok now. Thank you for your help again!