@Wayne-Workman
Yes, I tried both trunk and no trunk version.
The trunk version was more broken with my clients than the 1.2.0. Image upload would show the size of full disk (deploying to a disk with smaller total size would not work.). Normal deployment did not work at all either, it would only fail when starting.
@Wayne-Workman
Hello Wayne, sorry for the late feedback.
A lot of things have happened the last few weeks. I had my apprenticeship exam and also I had to finish the task regarding the clients I’ve been testing with.
I tried following the guides you referred but they did not work. It seems as when I had the combination of the latest version, ipxe.kkpxe, and the client (HP ProBook 455 G3), not even normal deployment would work. Uploading from this version seemed to create image files with the size of the disk (although used disk space on fog server was normal). The same happened both after cleaning and reinstallation of the server. (I followed all steps again and made it similar.
In the end I had to go with normal deployment on 1.2.0 fog server.
Hey, I’ve tested the client today.
At first the client would boot on network, get ip adress, try configure net0 be successful then end with dhcp failed. It then guides me to this page:
http://ipxe.org/err/040ee1
And I run
ifconf -c dhcp net0
Then the message says “Connection timed out” and guide me to:
http://ipxe.org/err/4c1060
Then i tried booting on an older client hp compaq 6735b and this one boots up alright.
So I changed in dhcpd.conf
class "Legacy" {
match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00000";
filename "undionly.kkpxe";
to
class "Legacy" {
match if substring(option vendor-class-identifier, 0, 20) = "PXEClient:Arch:00000";
filename "ipxe.kkpxe";
Then the newer client would boot, (in boot it first failed at configuring net0, 00:00:00:00:00, then it tried configuring net1, this was a legit address.)and i tried multicast, then it would complete the first setup and boot partclone, in partclone it says “Starting to restore image (-) to device (/dev/sda1)”, it stop at this window. After checking the server webgui, i saw that the image i was trying to download (i uploaded it at some point from a different computer) stood with 0B, i did a new upload and then it says 465GB, checking the disk with df -h:
root@ubuntu-fog:/etc/dhcp# df -h
Filesystem Size Used Avail Use% Mounted on
udev 2.8G 4.0K 2.8G 1% /dev
tmpfs 566M 1.2M 565M 1% /run
/dev/mapper/ubuntu--fog--vg-root 105G 21G 79G 21% /
none 4.0K 0 4.0K 0% /sys/fs/cgroup
none 5.0M 0 5.0M 0% /run/lock
none 2.8G 148K 2.8G 1% /run/shm
none 100M 24K 100M 1% /run/user
/dev/sda1 236M 41M 183M 19% /boot
Tried again to multicast, but stops at same window in partclone.
@Wayne-Workman said:
@emijoa said:
What os would you recommend to run fog on ?
CentOS 7
I might give that a go then the next time I reinstall. 
Will do! I’m new to Linux in general, I’ve tried a little ubuntu and debian. But I did ubuntu as it seemed to be the best documentet on the wiki 
What os would you recommend to run fog on ?
There is no service that is called dhcpd, however there is one called isc-dhcp-server, I believe this was installed by the 1.2.0 installer?
root@ubuntu-fog:/fog_git/bin# service --help
Usage: service < option > | --status-all | [ service_name [ command | --full-restart ] ]
root@ubuntu-fog:/fog_git/bin# service --status-all
[ ? ] FOGImageReplicator
[ ? ] FOGMulticastManager
[ ? ] FOGScheduler
[ + ] acpid
[ - ] anacron
[ + ] apache2
[ + ] apparmor
[ ? ] apport
[ + ] atd
[ + ] avahi-daemon
[ + ] bluetooth
[ + ] clamav-freshclam
[ ? ] console-setup
[ + ] cron
[ + ] cups
[ + ] cups-browsed
[ - ] dbus
[ ? ] dns-clean
[ + ] friendly-recovery
[ - ] gdm
[ - ] grub-common
[ ? ] irqbalance
[ - ] isc-dhcp-server
[ ? ] killprocs
[ ? ] kmod
[ ? ] mysql
[ ? ] networking
[ + ] nfs-kernel-server
[ ? ] ondemand
[ - ] php5-fpm
[ ? ] pppd-dns
[ - ] procps
[ - ] pulseaudio
[ ? ] rc.local
[ + ] resolvconf
[ + ] rpcbind
[ - ] rsync
[ + ] rsyslog
[ + ] saned
[ ? ] screen-cleanup
[ ? ] sendsigs
[ - ] ssh
[ - ] sudo
[ + ] tftpd-hpa
[ + ] udev
[ ? ] umountfs
[ ? ] umountnfs.sh
[ ? ] umountroot
[ - ] unattended-upgrades
[ - ] urandom
[ - ] x11-common
[ + ] xinetd
It came with this message
root@ubuntu-fog:/home/administrator# sudo service isc-dhcp-server stop
stop: Unknown instance:
root@ubuntu-fog:/home/administrator# sudo service isc-dhcp-server start
isc-dhcp-server start/running, process 7787
(I’ve been restarting this service whenever I changed the bootfile for testing.)
I ran the ./installfog.sh and it went through smoothly.
Logfile:
https://dl.dropboxusercontent.com/u/106805228/fog_error_5937.log
I’ll test and see if something is different on the clients tomorrow. Currently writing this from home.
No, it was at first a misspell, but i didn’t change it as it was only a test server. I’ve been reinstalling a few times already.
root@ubuntu-fog:/fog_git/bin# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
root@ubuntu-fog:/fog_git/bin# cat /etc/resolv.conf
Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
nameserver 192.168.1.1
The tutorial I followed wanted me to set static in this file.
root@ubuntu-fog:/fog_git/bin# cat /etc/network/interfaces
This file describes the network interfaces available on your system
and how to activate them. For more information, see interfaces(5).
The loopback network interface
auto lo
iface lo inet loopback
The primary network interface
auto eth0
iface eth0 inet static
address 192.168.1.101
netmask 255.255.255.0
gateway 192.168.1.1
dns-nameservers 192.168.1.1
root@ubuntu-fog:/fog_git/bin# cat /etc/dhcp/dhcpd.conf
DHCP Server Configuration file
see /usr/share/doc/dhcp*/dhcpd.conf.sample
This file was created by FOG
Definition of PXE-specific options
Code 1: Multicast IP Address of bootfile
Code 2: UDP Port that client should monitor for MTFTP Responses
Code 3: UDP Port that MTFTP servers are using to listen for MTFTP requests
Code 4: Number of seconds a client must listen for activity before trying
to start a new MTFTP transfer
Code 5: Number of seconds a client must listen before trying to restart
a MTFTP transfer
option space PXE;
option PXE.mtftp-ip code 1 = ip-address;
option PXE.mtftp-cport code 2 = unsigned integer 16;
option PXE.mtftp-sport code 3 = unsigned integer 16;
option PXE.mtftp-tmout code 4 = unsigned integer 8;
option PXE.mtftp-delay code 5 = unsigned integer 8;
option arch code 93 = unsigned integer 16; # RFC4578
use-host-decl-names on;
ddns-update-style interim;
ignore client-updates;
next-server 192.168.1.101;
Specify subnet of ether device you do NOT want service. for systems with
two or more ethernet devices.
subnet 136.165.0.0 netmask 255.255.0.0 {}
subnet 0.0.0.0 netmask {
option subnet-mask ;
range dynamic-bootp 0.0.0.10 192.168.1.254;
default-lease-time 21600;
max-lease-time 43200;
option domain-name-servers x.x.x.x;
option routers x.x.x.x;
filename "undionly.kpxe";
}
root@ubuntu-fog:/fog_git/bin# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:25:b3:11:ea:3d brd ff:ff:ff:ff:ff:ff
inet 192.168.1.101/24 brd 192.168.1.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::225:b3ff:fe11:ea3d/64 scope link
valid_lft forever preferred_lft forever
Here’s is also the fog settings, if that is interesting.
root@ubuntu-fog:/fog_git/bin# cat /opt/fog/.fogsettings
Created by the FOG Installer
Version: 1.2.0
Install time: Tue 05 Jan 2016 11:20:32 PM CET
ipaddress="192.168.1.101";
interface="eth0";
routeraddress="# option routers x.x.x.x;";
plainrouter="";
dnsaddress="# option domain-name-servers x.x.x.x; ";
dnsbootimage="";
password="69f422";
osid="2";
osname="Debian";
dodhcp="y";
bldhcp="1";
installtype="N";
snmysqluser="root"
snmysqlpass="";
snmysqlhost="localhost";
installlang="0";
donate="0";
fogupdateloaded="1"
Okay, that did the work, but now it stops at dhcp. Also, when i look in the dhcp they seem to have been changed.
* Stopping ISC DHCP server dhcpd
...fail!
dhcpd self-test failed. Please fix /etc/dhcp/dhcpd.conf.
The error was:
Internet Systems Consortium DHCP Server 4.2.4
Copyright 2004-2012 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
/etc/dhcp/dhcpd.conf line 35: expecting numeric value.
subnet 0.0.0.0 netmask {
^
/etc/dhcp/dhcpd.conf line 37: range declaration not allowed here.
range
^
/etc/dhcp/dhcpd.conf line 42: expecting a declaration
filename "undionly.kpxe";
^
Configuration file errors encountered -- exiting
Okay:
* Stopping FOG Computer Imaging Solution: FOGMulticastManager
start-stop-daemon: warning: failed to kill 1189: No such process
...done.
* Stopping FOG Computer Imaging Solution: FOGImageReplicator
start-stop-daemon: warning: failed to kill 1128: No such process
...done.
../lib/common/functions.sh: line 658: /etc/init.d/FOGSnapinReplicator: No such file or directory
* Stopping FOG Computer Imaging Solution: FOGScheduler
start-stop-daemon: warning: failed to kill 1215: No such process
...done.
../lib/common/functions.sh: line 658: /etc/init.d/FOGPingHosts: No such file or directory
stop: Unknown job: mysql
start: Unknown job: mysql
For the whole file:
https://db.tt/8lgK4hAM
Ubuntu 14.04.3, installed LAMP and SSH. Also installed a Minimal Gnome Core Desktop
I tried updating using git earlier today, it failed when trying to start my-sql.
Okay, what steps do I follow to upgrade or do I need a fresh install?
I also get this error message, currently trying to multicast clients using HP ProBook 455, I had to change the boot file for the fog to work on these clients. I’ve tested the different files under tftpboot and found that the only ones that work are : undionly.kpxe.INTEL, ipxe.kkpxe, ipxe.kpxe
I’m trying to run an isolated fog server with a built in dhcp, currently fog 1.2.0
I’ve changed the time for booting to disk in boot menu.