Cant PXE boot to fog server
-
Have you tested that things are working since you started seeing these issues?
-
At this point I would scour the BIOS and check settings, if you can pxe boot other clients and not this particular model, the problem most likely lies in the hardware, or the BIOS settings.
If adjusting the BIOS settings does not have an affect or if you have already exhausted all methods to enable the LAN Option Rom, Pxe boot options, Next server options, etc then I would contact Lenovo and see if there is a BIOS Flash that you can acquire to make the units PXE boot.
-
yes the M71z and M72z and hp elite books still upload and deploy with no issues, i also have already contacted lenovo and sent them a pc as well to tested a new bios on the machine here. lenovo states right out of the box the machine works but when they sent the machine back right out of the box it still dint pxe boot and all settings are the same in bios as they left them.
i dont know if this may help but Would knowing my setup help as well, cause to make this even weirder. the m71z, m72z have no problem pxe booting from a dell switch power connect 6224, but when i connect the m73z it never pxes boot . so i decide to take a direct connection from the wall and to the computer and took the switch out of the picture [ATTACH=full]575[/ATTACH] and it pxe boots but hangs here, let me know if this helps
[url=“/_imported_xf_attachments/0/575_rsz_hang_on_pc_from_wall_to_pc.jpg?:”]rsz_hang_on_pc_from_wall_to_pc.jpg[/url]
-
Looks like a problem with the kernel.
Try mine:
[url]https://mastacontrola.com/fogboot/kernel/bzImage32[/url] -
okay thank you would the kernel effect how it boots through a switch and why some devices work and others don’t?
-
No it shouldn’t, but we never know what could be causing an issue. If removing the switch fixes the problem, it would seem likely there was a problem with the switch in the first place.
-
okay im going to try the kernel ill update shortly with the findings thanks guys for all the help so far
-
Okay sorry to ask this but how do i upload that kernel though the web interface, or do i have to do it on the server ?
-
You will need to copy it over to the server and then set that kernel for that one host or all hosts(default kernel).
It goes in the directory /tftpboot/fog/kernel.
-
does the kernel update have to be updated through the server or can it be done through the gui
-
okay thank you
-
through the server for Tom’s custom kernel.
There are lots of defaults that can be done through the GUI but Tom’s requires you to add it without the GUI unless you go to FOG 33b.
-
okay thank you
-
how do i set it for the host or as the default kerenal for all hosts , sorry this is the first time Ive ever done any thing with the kerenals
-
You just copy it to the /tftpboot/fog/kernel/ directory as bzImage
A sample of commands you could perform this with would be:
[code]cd /tftpboot/fog/kernel/
mv bzImage bzImage.orig.2014MAR11
wget --no-check-certificate -O bzImage https://mastacontrola.com/fogboot/kernel/bzImage32
[/code]That should do the trick for you.
-
thank you so much
-
i found this thread while searching for my hardware. I’m not sure if my problem would be fixed by this kernel or not?
I have Lenovo M72z and it PXE boots ok, but if I choose (or it times out on the pxe menu) to the first option: “boot from local disk”… well, it doesn’t happen.
I get a black screen that says “Booting from local disk…” in the upper left corner, then it hangs there forever.
As far as I can tell, everything else seems to be ok. I can upload and deploy images. Sometimes when I multicast, one computer in the group (of five computers) won’t wake (for unknown reasons) and then the multicast will be stuck at “Please Wait” (blue screen) until I go power up the offending hardware. Then it takes off fine.
After I deploy an image, it tries to reboot and I get to the black screen “booting from local disk” hang (as noted above) again. When I hit ESC to skip the pxe menu, I can get in just fine… but then it will reboot once the first time after a deploy after a minute or so… I think this must be a delayed reboot command from FOG left over from the image deploy (because the black screen hang didnt ever complete successfully).
I did the hardware inventory option and I noticed a message fly by about unknown/unrecognized BIOS “please report”. Though I am not sure where to report this?
Here are the results from the hardware inventory of a typical machine:
System Manufacturer
LENOVOSystem Product
3554CTOSystem Version
ThinkCentre M72zSystem Serial Number
PBG8GDGSystem Type
DesktopBIOS Vendor
LENOVOBIOS Version
F6KT32AUSBIOS Date
09/03/2013Motherboard Manufacturer
LENOVOMotherboard Product Name
MAHOBAYMotherboard Version
NOKMotherboard Serial Number
Motherboard Asset Tag
CPU Manufacturer
Intel
CorporationCPU Version
Intel Core
i5-3470S CPU @ 2.90GHzCPU Normal Speed
2900 MHzCPU Max Speed
2900 MHzMemory
3433056 kBHard Disk Model
WDC WD10EZEX-08RKKA0Hard Disk Firmware
80.00A80Hard Disk Serial Number
WD-WCC1S6883074 -
[quote=“mkstreet, post: 27254, member: 24215”]i found this thread while searching for my hardware. I’m not sure if my problem would be fixed by this kernel or not?
I have Lenovo M72z and it PXE boots ok, but if I choose (or it times out on the pxe menu) to the first option: “boot from local disk”… well, it doesn’t happen.
I get a black screen that says “Booting from local disk…” in the upper left corner, then it hangs there forever.[/quote]
Change the exit type within the GUI. There are two types, exit and sanboot. For your setup, try with exit. It’s defaulted to sanboot.
Location is: FOG Configuration->FOG Settings->FOG Boot Settings->FOG_BOOT_EXIT_TYPE
-
[quote=“Tom Elliott, post: 27259, member: 7271”]Change the exit type within the GUI. There are two types, exit and sanboot. For your setup, try with exit. It’s defaulted to sanboot.
Location is: FOG Configuration->FOG Settings->FOG Boot Settings->FOG_BOOT_EXIT_TYPE[/quote]
Hi Tom,
Thanks for the reply. I will try that on Monday. Would this FOG_BOOT_EXIT_TYPE affect all exits to the local disk boot – and not just boots-after-deploy? I have this same get-stuck “Booting from local disk…” when I choose “1” from the PXE menu.
Do I need to be concerned about that message during FOG Hardware Inventory about unknown BIOS ?
Sorry about not including the version info. I’m using… Fog Vers: 0.32 O/S: Ubuntu 12.04.04 LTS (Pangolin)
-
FOG_BOOT_EXIT_TYPE is only relevant for .33+ versions of Fog.
does the computer boot properly when not connected to the network?
