Could not mount images folder Error
-
I am running version 1.5.5 of Fog. Its running on Hyper-V.
-
systemctl disable firewalld systemctl stop firewalldThen check the status of selinux
sestatusSELinux status: should be set to permissive.
Edit: For your new post, we need to see the error at the top (just off the top edge if the screen)
-
This error is interesting because it appears to be a network issue. The “no route to host” is the key. Is the target computer on a different subnet than the FOG server?
-
No the target computer is 10.2.227.199
-
@lschnider said in Could not mount images folder Error:
No the target computer is 10.2.227.199
Can you please schedule a fresh deploy task. But this time tick the checkbox for debug. Start up the client and when you get to the shell run the following commands to verify:
ip a s ping -c 3 10.2.227.200If the two machines are surely in the same subnet I suspect the error “No route to host” might come from the firewall being enabled on the FOG server and not allowing NFS access. Run
iptables -L -n -von the FOG server and post here. -
Here is the output from the first thing you said to do.
and here is the second
[root@localhost cmc_it]# iptables -L -n -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT udp -- virbr0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:53 0 0 ACCEPT tcp -- virbr0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 0 0 ACCEPT udp -- virbr0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:67 0 0 ACCEPT tcp -- virbr0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:67 140K 21M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 ctstate RELATED,ESTABLISHED 10190 612K ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 87460 13M INPUT_direct all -- * * 0.0.0.0/0 0.0.0.0/0 86467 13M INPUT_ZONES_SOURCE all -- * * 0.0.0.0/0 0.0 .0.0/0 86467 13M INPUT_ZONES all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 ctstate INVALID 80445 12M REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * virbr0 0.0.0.0/0 192.168.122. 0/24 ctstate RELATED,ESTABLISHED 0 0 ACCEPT all -- virbr0 * 192.168.122.0/24 0.0.0.0/0 0 0 ACCEPT all -- virbr0 virbr0 0.0.0.0/0 0.0.0.0/0 0 0 REJECT all -- * virbr0 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable 0 0 REJECT all -- virbr0 * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 ctstate RELATED,ESTABLISHED 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 FORWARD_direct all -- * * 0.0.0.0/0 0.0.0.0 /0 0 0 FORWARD_IN_ZONES_SOURCE all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 FORWARD_IN_ZONES all -- * * 0.0.0.0/0 0.0.0 .0/0 0 0 FORWARD_OUT_ZONES_SOURCE all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 FORWARD_OUT_ZONES all -- * * 0.0.0.0/0 0.0. 0.0/0 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 ctstate INVALID 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT 132K packets, 78M bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT udp -- * virbr0 0.0.0.0/0 0.0.0.0/0 udp dpt:68 132K 78M OUTPUT_direct all -- * * 0.0.0.0/0 0.0.0.0/ 0 Chain FORWARD_IN_ZONES (1 references) pkts bytes target prot opt in out source destination 0 0 FWDI_public all -- eth0 * 0.0.0.0/0 0.0.0.0/0 [goto] 0 0 FWDI_public all -- + * 0.0.0.0/0 0.0.0.0/0 [goto] Chain FORWARD_IN_ZONES_SOURCE (1 references) pkts bytes target prot opt in out source destination Chain FORWARD_OUT_ZONES (1 references) pkts bytes target prot opt in out source destination 0 0 FWDO_public all -- * eth0 0.0.0.0/0 0.0.0.0/0 [goto] 0 0 FWDO_public all -- * + 0.0.0.0/0 0.0.0.0/0 [goto] Chain FORWARD_OUT_ZONES_SOURCE (1 references) pkts bytes target prot opt in out source destination Chain FORWARD_direct (1 references) pkts bytes target prot opt in out source destination Chain FWDI_public (2 references) pkts bytes target prot opt in out source destination 0 0 FWDI_public_log all -- * * 0.0.0.0/0 0.0.0. 0/0 0 0 FWDI_public_deny all -- * * 0.0.0.0/0 0.0.0 .0/0 0 0 FWDI_public_allow all -- * * 0.0.0.0/0 0.0. 0.0/0 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 Chain FWDI_public_allow (1 references) pkts bytes target prot opt in out source destination Chain FWDI_public_deny (1 references) pkts bytes target prot opt in out source destination Chain FWDI_public_log (1 references) pkts bytes target prot opt in out source destination Chain FWDO_public (2 references) pkts bytes target prot opt in out source destination 0 0 FWDO_public_log all -- * * 0.0.0.0/0 0.0.0. 0/0 0 0 FWDO_public_deny all -- * * 0.0.0.0/0 0.0.0 .0/0 0 0 FWDO_public_allow all -- * * 0.0.0.0/0 0.0. 0.0/0 Chain FWDO_public_allow (1 references) pkts bytes target prot opt in out source destination Chain FWDO_public_deny (1 references) pkts bytes target prot opt in out source destination Chain FWDO_public_log (1 references) pkts bytes target prot opt in out source destination Chain INPUT_ZONES (1 references) pkts bytes target prot opt in out source destination 86449 13M IN_public all -- eth0 * 0.0.0.0/0 0.0.0.0/0 [goto] 17 2689 IN_public all -- + * 0.0.0.0/0 0.0.0.0/0 [goto] Chain INPUT_ZONES_SOURCE (1 references) pkts bytes target prot opt in out source destination Chain INPUT_direct (1 references) pkts bytes target prot opt in out source destination 993 35276 ACCEPT 2 -- * * 0.0.0.0/0 0.0.0.0/0 Chain IN_public (2 references) pkts bytes target prot opt in out source destination 86466 13M IN_public_log all -- * * 0.0.0.0/0 0.0.0.0/ 0 86466 13M IN_public_deny all -- * * 0.0.0.0/0 0.0.0.0 /0 86466 13M IN_public_allow all -- * * 0.0.0.0/0 0.0.0. 0/0 1 84 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 Chain IN_public_allow (1 references) pkts bytes target prot opt in out source destination 2 104 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ctstate NEW 5600 1517K ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpts:49152:65532 ctstate NEW 408 21352 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ctstate NEW 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 ctstate NEW 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:69 ctstate NEW 11 679 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:69 ctstate NEW Chain IN_public_deny (1 references) pkts bytes target prot opt in out source destination Chain IN_public_log (1 references) pkts bytes target prot opt in out source destination Chain OUTPUT_direct (1 references) pkts bytes target prot opt in out source destination```Im guessing it has something to do with every ip being 0.0.0.0/0
-
@lschnider Ok, so client can reach the server but firewall is enabled. Disable it for now and see if the deploy is working then. This looks like a CentOS ruleset. So I may ask if you have followed our wiki article on CentOS and disabled SELinux (and the firewall)??! I wonder how you were able to capture an image if the firewall was enabled all the time. Run the following command to switch off the firewall temporarily and then try to do another deploy:
systemctl stop firewalld -
I actually am trying to capture an image not deploy one. I havent been able to successfully capture one yet. I did follow the article but i definitely could have missed a step or something. I will try it with the firewall off and see if that works.
-
Okay so it looks like its capturing the image now, i went back through the wiki article you sent me and followed all the steps again. and everything said “Warning already enabled” the only one that I wasnt sure about was the
what command do i actually run in this.Also when it finished capturing the image it went to this
It did not successfully capture the image after that.
-
systemctl disable firewalld systemctl stop firewalldThen check the status of selinux
sestatusSELinux status: should be set to permissive.
Edit: For your new post, we need to see the error at the top (just off the top edge if the screen)
-
[root@localhost cmc_it]# sestatus SELinux status: enabled SELinuxfs mount: /sys/fs/selinux SELinux root directory: /etc/selinux Loaded policy name: targeted Current mode: permissive Mode from config file: permissive Policy MLS status: enabled Policy deny_unknown status: allowed Max kernel policy version: 31 -
@lschnider You will still have an issue. You did not follow the prerequisites for installing FOG.
Now you need to edit /etc/selinux/config
In that file edit
SELINUX=enforcing
to read
SELINUX=permissivereboot the fog server.
-
@lschnider scratch that, it is set to permissive. I did not read well enough.
OK we need to see the error that is just off the top of the screen in your previous picture.
-
@lschnider Also I’ve seen that date.timezone warning message before. I don’t know if that is something new with 1.5.5 or not. Can you confirm that this FOG setting is correct for your timezone: FOG Configuration->FOG Settings->General Settings->TZ INFO
-
Well maybe this is a dumb question but how do you scroll up on that screen. I have been trying to but it wont let me.
-
@george1421 The date/time was wrong. I fixed that, i will try to run the capture again.
-
@lschnider You can’t it a character mode terminal. If its scrolled off the top of the screen then its lost. Lets see if we can fix the TZ issue so those warning messages will go away.
Let me ask you have you messed with / changed the password for the FOG linux service account called
fog? This is not the default webui admin called fog this is the linux user calledfog? If you changed this account I might expect this error message at this point in the capture process. -
@lschnider said in Could not mount images folder Error:
@george1421 The date/time was wrong. I fixed that, i will try to run the capture again.
You may need to reboot the fog server for that setting to get installed.
-
@george1421 no i dont believe i have. Is there a way to tell if the password is like it should be?
-
@lschnider There is a hidden file /opt/fog/.fogsettings The linux user account for fog is listed in there.
Test from a windows computer, ftp to the fog server. Login as
fogand the long password from the .fogsettings file. If that works then we need to look at the configuration. -
@george1421 okay i tried to ftp and it says
I will try to get a picture of that error you asked about earlier.
