Boot loop after imaging UEFI
-
@jemerson93 said in Boot loop after imaging UEFI:
It will image, but get stuck in the REFIND boot loop.
Try different exit types for that particular host. You register your hosts, right?
-
Also what version of fog?
-
@Wayne-Workman @Tom-Elliott As an update, I have completed the steps on the BIOS & UEFI coexistence in the link previously.
I complete a full host registration prior to imaging.
Current version of Fog is 1.5.2.
I could try using a different exit type for that host but I’m running into the REFIND issue with quite a few Dell laptops we received today.
-
Couple other bits of information is that after imaging the hard drive, the BIOS shows NIC IPV4 and NIC IPV6 but no other boot devices.
Disabling those as the boot devices leaves No boot device found.
Most recent kernels are installed as well.
-
@jemerson93 said in Boot loop after imaging UEFI:
I could try using a different exit type for that host but I’m running into the REFIND issue with quite a few Dell laptops we received today.
You can set your global default inside of
web gui -> FOG Configuration -> FOG Settingsuse your browser’s search feature withctrl+fand look for the wordexit. Also, you can also set exit types for particular hosts via groups in-mass. So there are options there that allow you to do less repetitive work. So my suggestion is still to try different exit types. -
@wayne-workman @Tom-Elliott As an update, I’ve tried multiple exit modes and have ran into chainloading failed with those.
Another instance I noticed is after the imaging is completed, if I enter the BIOS, I have the usual NIC IPV4 and IPV6 but no other boot devices such as Windows Boot Manager or hard drive.
Kind of at a loss on what I am missing for UEFI to work. I’ve gone through and verified that I’ve done everything located below.
https://wiki.fogproject.org/wiki/index.php?title=BIOS_and_UEFI_Co-Existence -
@jemerson93 It sounds like your DHCP is working correctly - your problem is with the exit modes. What exact models of systems are you having these problems on?
-
@wayne-workman Currently the issue is residing on Dell Latitude 5590s. Received a few new ones to deploy and all are experiencing this issue.
-
@wayne-workman Update: Also happening on Dell Latitude 7480s. Only support UEFI. Below is how this one was imaged
UEFI Network Stack enabled
Secure Boot disabled
SATA changed to ACHIStuck in REFIND loop. If exit type is changed, receiving a chainloading fail.
Earlier I tested an old workstation set to Legacy and imaged fine. Still thinking it’s an issue with UEFI or my image.
Currently I have 1 master image being used (split off into multiple smaller images). Sysprep it and upload to Fog. I don’t have separate images for Legacy/UEFI. Should I create a specific image a certain way for only UEFI machines?
-
@jemerson93 said in Boot loop after imaging UEFI:
I don’t have separate images for Legacy/UEFI. Should I create a specific image a certain way for only UEFI machines?
You absolutely need an image for Legacy and an image for UEFI. One does not work on the other.
Have you tried every exit type individually? Are you fully turning off the system between each try? A simple ctrl+alt+delete does not clear the firmware memory properly and will botch a retry of a different exit type. -
@wayne-workman That could be a big issue though. I am creating my images via a VM. Anything specific I should look at for creating a UEFI based image?
I did do CTRL ALT DELETE to test each exit so I can power off and go from there.
-
@jemerson93 said in Boot loop after imaging UEFI:
Anything specific I should look at for creating a UEFI based image?
Not really, if FOG is capturing it successfully then you’re good to go for that part.
@george1421 any ideas with the refind loop?
-
@wayne-workman As another update, I’ve tested all exit types and all have failed to boot.
Exit gives me a chainloading fail
The rest just keep doing the boot to hard drive in FogI edited the /var/www/html/fog/service/ipxe/refind.conf to scanfor internal,external,hdbios,biosexternal and timeout to 0 per another forum post and still no luck.
Again, even after imaging, BIOS shows both NIC boots but no other boot device (such as Windows Boot Manager) or a hard drive. Believe all laptops being affected are M2 SSD’s. Unsure if they are nvme.
-
@jemerson93 said in Boot loop after imaging UEFI:
Believe all laptops being affected are M2 SSD’s. Unsure if they are nvme.
Then it may be that there is something wrong with the imaging process - it may be that the exit types are working fine but the local disk simply isn’t bootable. Are there any errors during image capture or deploy?
-
@wayne-workman I do not notice any errors during capture or deploy.
-
@wayne-workman curiosity question as I was doing some more research. My current image I’m testing is formatted as a MBR partition. I read that UEFI needs to be formatted as GPT to be bootable. I just created a VM (using Proxmox) as UEFI bios and converted it to GPT. Going to upload it to Fog in the am. Think that could deal with the REFIND loop?
-
@jemerson93 If the image was captured/deployed to a disk in MBR format, UEFI would indeed not find the drive as the disks MUST be in GPT format.
-
@tom-elliott Thank you for the clarification. I will finish uploading the image in the morning and post an update.
-
As an update, after creating a GPT partitioned image and uploading it to FOG, the image will successfully boot.
The only issue I have now is that I still receive the REFIND menu. It allows me to boot into the OS afterwards, but each time it boots (unless I disable network boot), it will go into the REFIND menu. Is there a way to either, edit the conf file to not display REFIND or to fix the issue with it not detected a CSM?
I have not tried other exit types after fixing the image so if this is how REFIND will be, I can re-attempt other exit methods.
On a side note, thank you to everyone for the assistance. I did not even realize that UEFI used GPT partitions to boot.
-
@Tom-Elliott
After some more troubleshooting I am still stuck on trying to skip the REFIND screen. I will have some screenshots below. I’ve attempted to remove all scanfor BIOS options from refind.conf with no luck. If I enter any key, I can boot to the OS. I’m trying to find how to remove this scan as I’m trying to make the UEFI imaging as automated as the BIOS imaging. Images below…After imaging
After inputting any key
