• Recent
    • Unsolved
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    • Register
    • Login

    FOG kernel stalling out after PXE boot

    Scheduled Pinned Locked Moved
    FOG Problems
    7
    30
    17.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • B
      Bob Fillmore
      last edited by

      OK, I swapped out the Quadro 2000 and tossed in a Geforce 9800GTX+ and PXE boots past the initial FOG menu. It complaines that the BIOS for the Z400 is unknown, but appears to function as expected. I’m going to pull an image now and see how it goes. 🙂

      1 Reply Last reply Reply Quote 0
      • P
        Peter Smee
        last edited by

        Hey Bob, I did the same and it worked also, and I get the same unknown error on the MB too. I am lucky to have onboard Intel HDMI out that I just enable to image, I have also found that enabling the onboard video the computers will still image, though they will not show anything on the screen this is using the [FONT=Ubuntu][COLOR=#333333]Kernel - 2.6.36.1 Core.[/COLOR][/FONT]

        1 Reply Last reply Reply Quote 0
        • B
          Bob Fillmore
          last edited by

          Looks like we now have a problem with the RAID. The workstations are using the MOBO built in raid controller to have the 2 HDs in RAID0 to increase performance. The 0.29 kernel didn’t see anything and just crashed, so I switched back to the old kernel and got an image. Unfortunatley, dropping the image back boots to a “Non system disk” error…

          1 Reply Last reply Reply Quote 0
          • P
            Peter Smee
            last edited by

            Did you build the image on the RAID? If yes try these instructions to see if it’s the boot sector then re-sysprep and re-image from that machine. [url]http://www.heiser.net/posts/3256[/url]

            1 Reply Last reply Reply Quote 0
            • B
              Bob Fillmore
              last edited by

              Yes; the image was built on a RAID. Tried the steps from the link you provided and the link that page referenced, but as far as DISKPART goes, it thinks the DISK has no partitions so none of that works.

              1 Reply Last reply Reply Quote 0
              • B
                Bob Fillmore
                last edited by

                At the risk of being accused of Thread Necromancy, I wanted to check in on these issues.

                Seems that the OP & my initial issue was indeed caused by the Quadro in my case. Since my last post, I have researched Linux kernel-making, and have cooked up a kernel that now boots fine with the Quadro in the machine. Unfortunately, I am still unable to have FOG see the built-in Intel RAID controller properly (Firmware-RAID), and just can’t figure out how to get the kernel to see the RAID container instead of the individual disks… I see many posts about this issue with no solutions, and would very much like to get a solution.

                1 Reply Last reply Reply Quote 0
                • T
                  ttcircus
                  last edited by

                  Nice one Bob! I had the exact same problem with the same hardware (z400), i swapped the quadro for a cheap geforce and it did the trick! Thanks!

                  [quote=“Bob Fillmore, post: 1085, member: 294”]OK, I swapped out the Quadro 2000 and tossed in a Geforce 9800GTX+ and PXE boots past the initial FOG menu. It complaines that the BIOS for the Z400 is unknown, but appears to function as expected. I’m going to pull an image now and see how it goes. :)[/quote]

                  1 Reply Last reply Reply Quote 0
                  • B
                    Bob Fillmore
                    last edited by

                    Glad my efforts helped someone. 😄

                    Unfortunately, the lack of Firmware RAID support was a show stopper for us and I was forced to box my FOG servers and go with Acronis Snap Deploy. 😞

                    I really like what FOG has to offer and I hope that someone will figure out this Firmware Raid issue so that we can go back to FOG in the future. 🙂

                    1 Reply Last reply Reply Quote 0
                    • B
                      Bob Fillmore
                      last edited by

                      This post is deleted!
                      1 Reply Last reply Reply Quote 0
                      • K
                        Kevin McCaughey
                        last edited by

                        Also got a Z68XP-UD3 Gigabyte mobo and no dice for me. Wondering did anyone get it to work?

                        1 Reply Last reply Reply Quote 0
                        • 1
                        • 2
                        • 2 / 2
                        • First post
                          Last post

                        193

                        Online

                        12.0k

                        Users

                        17.3k

                        Topics

                        155.2k

                        Posts
                        Copyright © 2012-2024 FOG Project