Fog wont install
-
By the way,Am i supposed to use my public ip? (unrelated)
-
Your public IP is not what should be used. You would use the IP address your fog server is setup for within your internal network (the network you’re trying to image from).
Can you do me a favor and check the install. I’ll download a copy of the tar file and see what it’s doing as well, but I’ve never seen any issues with it before. Maybe it’s forgetting a part for Fedora 19 which is RH Based.
I’ll double check, but do you know how to edit the files?
From the install folder, look within for a folder that contains redhat and which files do the install process. I will get back here with the info, but it’s going to be a little bit.
-
Okay, looking into this, I don’t think there’s an issue with the default installation files for redhat. Fedora 19 should use the yum install mysql mysql-server and the configuration is chkconfig mysqld on; service mysqld restart which, you stated, works fine for your system.
However, it may have an issue because it’s trying to restart the service from your public IP address, which would cause a failure as it, theoretically, can’t access from that point.
Try not using your public IP address and use your server’s internal IP address during the setup. Hopefully this helps out.
-
This post is deleted! -
I know how to edit them,but i don’t know where to edit them.Also,where do i find my servers internal ip
-
This post is deleted! -
Is your fog server connected directly to the internet? You understand linux and the command line?
The way to obtain your systems IP (which you should have setup statically) is to run:
ifconfig
If you have multiple interfaces, you’ll need to figure out which interface you’re trying to use and use the IP associated with that.I assume your IP is going to be in the range of 192.168.1.2 thru 192.168.1.254 as you put your router and dns server as 192.168.1.1
Your files to be edited should be located in:
<locationOfFogInstallFolder>/lib/redhatThere are two files in there which I forget the names of.
However, if my memory serves me correctly, when you do the install, it should ask you what you want to set your IP up as, and it defaults to your systems IP, so unless your FOG server is directly connected to the Modem, it should have a private IP address assigned to it already. I’d recommend, until you understand what this software is doing, sticking with the defaults.
-
it doesn’t tell me the ip i should use.I found the ip,still not installing.And my isp wont allow me to have a static ip anyway.But i am ok with changing it all the time
-
it looks like the code to check the packges is this:
confirmPackageInstallation()
{
for x in $packages
do
echo -n " * Checking package: $x";
rpm -q $x >/dev/null 2>&1;
if [ “$?” != “0” ]
then
echo “…Failed!”
exit 1;else echo "...OK"; fi done;}
and the configue mySQL code is here:
configureMySql()
{
echo -n " * Setting up and starting MySql";
chkconfig mysqld on;
service mysqld restart >/dev/null 2>&1;
service mysqld status >/dev/null 2>&1;
if [ “$?” != “0” ]
then
echo “…Failed!”;
exit 1;
else
echo “…OK”;
fi
}
I do have some command line experence -
Okay,
Is your FOG Server behind a router that then connects to a modem or directly connected to the modem?
If you’re connected directly to the modem, then how did you get the DHCP Server and the DNS Server IP Address?
You’re sure mysql is actually running on your system then?
Is selinux running or disabled?
To check:
cat /etc/sysconfig/selinuxLook for:
SELINUX=disabled
If it doesn’t say disabled change it and reboot your machine.
Then check that iptables is disabled <- DONT DO THIS IF YOU’RE CONNECTED DIRECTLY TO THE MODEM
service iptables stop; chkconfig iptables off
Once done, retry the install process.
Can you post a reading of:
/var/log/messages
Directly after you’ve tried installing fog.
Thank you, -
Also,
When giving information, please try to provide as much information as possible. It’s not easy to troubleshoot something when not being directly in front of it. It makes it much more difficult to help out when there isn’t any information to go off of.
Responses such as:
“didn’t work.”,“Didn’t help”Doesn’t give us anything to work off. We don’t know what you’ve tried, or how you know certain things.
How do you know that mysql is working?
What have you tried beyond the help I’ve tried giving?
What kinds of error messages is the system telling you? Fog tells you information, but we don’t know your systems particular setup. -
sorry for the late reply. i connected to the router that connects me to the modem.i know that mysql is working because when enter mysql in the command line,it dosen’t give me any errors.
I downloaded the rpms for mysql and that didn’t work. the command you gave me finally worked.
i disabled iptables and selinux some time ago. -
Okay,
Is there any way you’d be able to allow remote access that I could actually take a look at the file/install process?
There shouldn’t be any problem with installing, so it seems there’s a borked command in the installer somewhere, I just don’t know where. I’m running on CentOS 6.4 and I haven’t run into any issues. I’m also running/testing 0.33 so I’m not a good example.
-
0.33?How do you download that
-
Are you trying to do this install from your home system?
Give me a minute or two and I’ll post the latest and greatest that I’ve created.
I don’t know if it will work, but it will contain many of the Fixes I’ve already implemented.
-
Ready for download:
-
getting the same error.I will remove mysql and see what happens this time
-
This post is deleted! -
Any luck yet?
What do you mean remove MySQL? Do you mean you’re uninstalling it, or not allowing fog to deal with the install of it?
Also, did you find your private IP for your system? The sock isn’t going to connect on your public IP address which could be your entire holdup.
My best suggestion is to find out what IP’s your router distributes for DHCP. (Usually something like: 192.168.1.100 thru 192.168.1.200)
Then statically set your FOG Server’s IP to something out side that scope (Like : 192.168.1.10)
Then when you go thru the installer, set your Server’s IP Address to 192.168.1.10
Your Router IP Address would then be set to 192.168.1.1
Your DNS IP would then be 192.168.1.1Because you’re not trying to access your fog system using the internet, (your public IP Address), the system shouldn’t have any issues finding your system during the mysql part. Then again, I don’t know, I’m not there to see the issue either.
-
with 0.33,it dectects my ip and eveything.I have a internet connection.Same error about mysql.
And how to find out my dhcp router ip?
do i go to my router settings?
