Deploy image not expanding partitions

[SuperMajestic]

@Tom-Elliott


Other time, error

[Tom Elliott]

@SuperMajestic I don’t understand.

I see the pic, and it appears to be working.

[SuperMajestic]

@Tom-Elliott said in Deploy image not expanding partitions:

I don’t understand.
I see the pic, and it appears to be working.

In first pic. To the end show “Resizing… Failed”.

[Tom Elliott]

@SuperMajestic Yes, but this is before FOG has even started collecting the information.

We run e2fsck on each partition before it tries to resize it. So if there’s a problem on the disk, it will break things.

[SuperMajestic]

@Tom-Elliott Then… is problem of the disk? I don’t believe. In normal installations (by iso) I can install without problems.

Now, I going to change the disk drive by a 500GB and install a OS and test capture.

[Tom Elliott]

@SuperMajestic I don’t know what the issue is, I just know “of” the issue.

I have installed CentOS 7 MBR and GPT and can upload/deploy them just fine (though most of my work yesterday was around expanding extended partitions).

[SuperMajestic]

@Tom-Elliott Ok, then I have a important problem. Can’t use fog. I don’t understand because before I could capture a os and now not :-S

I changed de disk drive and deploy an image to test capture.

[Tom Elliott]

@SuperMajestic What do you mean?

I need information.

For example, deploy, boot into system.

Before running fog, as we know it will likely fail on the checking the partition area, run:

e2fsck -fp /dev/sd1

What does it show?

[SuperMajestic]

@Tom-Elliott The problem is in capture, not in deploy. Since yesterday any capture works with GPT.

Now, I going to install centos manually, without intervention of fog. And after, I try to capture again.

[SuperMajestic]

@Tom-Elliott said in Deploy image not expanding partitions:

k -fp /dev/sd1

Hello, I have the result :

http://imgh.us/result_6.jpg

[SuperMajestic]

@Tom-Elliott The new picture have all results of test all partitions.

[Tom Elliott]

@SuperMajestic the sda3 didn’t need to be done, only ext formatted volumes need to be tested.

[Tom Elliott]

for clarity, this was done before FOG ran, but after clean install, right?

[SuperMajestic]

@Tom-Elliott Yes, sorry, sda3 is a swap partition.

[SuperMajestic]

@Tom-Elliott

Yes.

1. Without fog, I installed fresh installation of Centos 7. I see that it works. The installation is finished correctly, and I see the root login.
2. I created the host on fog client and created the capture task.
3. Reboot the server with force pxe.
4. were Typed e2fsck -fp /dev/sda1
5. I’m waiting your instructions before run “fog” command.

[SuperMajestic]

@Tom-Elliott More info, I print fdisk result:

/dev/sda1 is a necessary partition to bios with GPT, type “BIOS boot”.
/dev/sda2 is a boot partition
/dev/sda3 swap
/dev/sda4 /

[SuperMajestic]

This is the last test. Now fsck is correct but crash in resizing sda2 (/boot).

[SuperMajestic]

This is the content of generated d1.partitions

[SuperMajestic]

@Tom-Elliott it’s incredible Now can’t capture nothing. gpt and mbr not works. Nothing :-S. Error in resizing sda1 even in two different hosts.

[Tom Elliott]

@SuperMajestic The capture logic hasn’t changed. Would you mind re-running the installer though?

Another dev found that there were two issues accidentally added to the capture. (But have been fixed for a bit).

The start position during our resizing was accidentally being shifted around (which could cause what you’re describing). I’ve tested capturing both gpt and mbr, and all is working from my side. I’ve tested deploying both gpt and mbr now and am fairly sure I’ve fixed the issues with the resizing now too.

So please, re-run the installer and hopefully things will go better.